61911-FAG bearing: complete specifications & equivalents

Specification table

Source: catalog reference (HR 1 Rolling Bearings (Jan 2020)) · extracted 2026-09-25

Parameters extracted from the official FAG Rolling Bearings catalogue (HR 1 Rolling Bearings (Jan 2020)); FAG® is a trademark of Schaeffler Technologies AG & Co. KG, used here for identification only — mpnbase is not an authorized FAG/Schaeffler distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at schaeffler.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61911-FAG model number is decoded

61911 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the thin 619xx section (diameter series 9 of ISO 15), multiplying bore code 11 by five gives the 55 mm bore; the 80 mm outside diameter and 13 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 55 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the Schaeffler HR 1 catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes 2Z (steel shields), 2RZ (non-contact rubber seals) and 2RSR (lip-contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Temperature rise and interference fits consume internal clearance on this 55 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 61911 with C3 for those conditions.
• The 619xx thin section (12.5 mm section height at 55 mm bore) trades load capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.
• Storage matters for open bearings: 61911-FAG leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Open bearings tolerate the highest speeds in the 61900-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 61911 units.
• Vibration during standstill brinells the raceways of a 55 mm bearing at ball spacing; if the machine sits idle next to running equipment, turn the shaft over periodically or isolate the arrangement.
• Deep-groove ball bearings tolerate only minutes of misalignment; if the 80 mm housing cannot be aligned, switch to a self-aligning type rather than shimming 61911-FAG.
• The open 61911 has no integral sealing; in the Schaeffler HR 1 catalogue the protected variants carry suffixes 2Z (two steel shields), 2RZ (two non-contact rubber seals) and 2RSR (two lip-contact rubber seals). Do not confuse FAG's 2RZ with a contact seal — the RZ lip does not touch the inner ring, which is why its speed capability stays close to the open bearing.
• FAG rates 61911 at 12100 r/min mechanical limiting speed (thermal reference speed 7500 r/min) — electric-motor territory; prefer the open or 2Z execution (sealed 2RSR variants lose roughly a third of the thermal speed) and confirm grease life at the reference speed for continuous running.
• At 55 mm bore 61911 is in Schaeffler's upper general-purpose range; the pressed steel cage is standard but mid-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for shock or very-low-speed duty — confirm cage material with the Schaeffler channel if the application sees impact loads.
• At 17.7 kN dynamic load rating (C) and 14.1 kN static (C0), 61911 is a medium-load FAG bearing for most electric-motor and pump duty; check the static safety factor against C0 for preloaded or thrust-loaded arrangements.
• At 180 g, 61911 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 55×80×13 mm envelope of 61911 gives a D/d ratio of 1.45 and 12.5 mm radial section height — a thin FAG section that saves space but is sensitive to misalignment and shock; keep the housing round within IT7 and the shaft deflection below the raceway contact envelope.
• The 17.7/14.1 kN load ratings, mass 180 g here are Schaeffler HR 1 Rolling Bearings (Jan 2020) catalogue figures for 61911-FAG on the 55×80×13 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61911 in a rated drive. Where FAG has since released an X-life version of this size, its expanded C/C0 ratings supersede the HR 1 print values quoted here.
• For hot shafts above roughly 100 °C continuous, consult Schaeffler about seal material and grease options for the 2RSR execution of 61911; the standard NBR lip is the economical general-duty choice, not the high-temperature one.
• FAG sealed units arrive greased for life with a lithium-soap fill; Schaeffler quotes a shelf life for greased bearings and recommends running stock first-in-first-out rather than re-greasing aged sealed units.