61911-ZZ-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61911-ZZ-NTN model number is decoded

In the 61900-series (diameter series 9 of ISO 15) the last two digits encode the bore: 61911 carries bore code 11 = 55 mm. Outside diameter 80 mm and width 13 mm come from the ISO 15 boundary-dimensions general plan. Suffix -ZZ denotes two non-contact metallic shields; they retain grease and block coarse debris but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 55 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NTN catalogue order number: 6911ZZ (suffix ZZ), two non-contact steel shields, mapped here from the industry-neutral -ZZ spelling.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Interference on a 55 mm shaft plus running heat consumes radial clearance: where the shaft runs hot or the fit is tight, order 61911 with C3 clearance and re-check the residual value after mounting.
• The 619xx thin section at 55 mm bore (12.5 mm section height) cannot shrug off the misalignment a standard section tolerates; keep the housing bores round and aligned, or edge contact will spall the raceways early.
• ZZ shields are non-contact: 61911-ZZ-NTN blocks chips and coarse dust but is not waterproof — do not install it expecting a pressure-wash seal, step up to 61911-2RS for that.
• Do not wash 61911-ZZ-NTN in solvent before mounting: the grease inside the shielded cavity is the service fill, and solvent creeping past the shield gap strips it out.
• Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 13 mm-wide ring of 61911-ZZ-NTN drags the lip and overheats it.
• Grease compatibility is not guaranteed between fills: mixing lithium and polyurea thickeners in a 61900-series position can soften the mixture and leak — clean out the old fill before switching grease types.
• NTN catalogues the shielded version as 6911ZZ — suffix ZZ, two non-contact steel shields. The industry-neutral page spelling is -ZZ; quote the NTN order number when buying through an NTN channel.
• At 55 mm bore 61911 is in NTN's upper general-purpose range; the pressed-steel cage is standard but mid-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NTN channel if the application sees impact loads.
• At 5500 r/min the grease limiting speed for 61911 covers medium-duty industrial drives; the open or shielded execution can run continuously at this speed with standard lithium-soap grease.
• At 17.7 kN dynamic load rating (C) and 13.3 kN static (C0), 0.92 kN fatigue load limit Cu, 61911 is a medium-load bearing suitable for most electric-motor and pump duty; the C0/C0r ratio matters for preloaded or thrust-loaded arrangements, so confirm the static safety factor with the NTN catalogue.
• At 180 g, 61911 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 55×80×13 mm envelope of 61911 gives a D/d ratio of 1.45 and 12.5 mm radial section height — this thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 17.7/13.3 kN load ratings, 0.92 kN fatigue load limit Cu NTN lists the grease limiting speed at 5500 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 180 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6911ZZ on the 55×80×13 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61911 in a rated drive.
• NTN's pressed-steel cage (no cage suffix) is the quiet standard for this size; for sustained running close to the limiting speed or for heavy shock duty, ask the NTN channel whether a machined-cage execution of 61911 is listed.
• Two NTN bearings of the same designation from different production lots can carry minor internal-geometry revisions; for paired or preloaded arrangements on one shaft, order a single lot through the NTN distributor.