61912-2RS bearing: complete specifications & equivalents
The 61912-2RS is a ISO 15 radial bearing sized 60 x 85 x 13 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Bore diameter d | 60 mm |
| Outer diameter D | 85 mm |
| Width B | 13 mm |
| Material | GCr15 |
| Seal / shield | 2RS |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 16.5 kN |
| Basic static load rating C0 | 12 kN |
| Fatigue load limit Pu | 0.6 kN |
| Limiting speed (mechanical) | 4500 rpm |
| Operating temperature | -30 to +110 °C |
| Mass | 210 g |
| Manufacturer designation | SKF 61912-2RS1 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-24 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 61900-series range
| Bore d | 2.362 in |
|---|---|
| Outer diameter D | 3.346 in |
| Width B | 0.512 in |
| ISO bore code | 12 |
| Radial section height (D−d)/2 | 12.5 mm |
| Smallest bore in 61900-series | 10 mm |
| Largest outer diameter in 61900-series | 420 mm |
| Width range across 61900-series | 6–56 mm |
| Bore position in 61900-series (smallest first) | 13 of 35 |
| Bore above smallest 61900-series size | 50 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 61912-ZZ | GENERIC-ISO | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 60×85×13 mm envelope per ISO 15; seal variant differs (2RS vs ZZ) — confirm sealing suits the duty. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 61912-2RS model number is decoded
In the 61900-series (ISO 15 diameter series 9) the last two digits encode the bore: 61912 carries bore code 12 = 60 mm. Outside diameter 85 mm and width 13 mm come from the ISO 15 boundary-dimensions general plan. Suffix -2RS denotes two contact-type elastomer seals over a lifetime grease fill; the sealing lips add drag compared with open or shielded versions. For normal-load mounting with a rotating inner ring on a 60 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude.
Typical equipment & failure modes
Common applications
- textile machinery
- packaging machinery
- space-constrained gearboxes
- clutch and transmission assemblies
Known failure patterns
- seal-lip hardening and loss of pre-grease in sustained high-temperature service
- grease-life expiry in the sealed-for-life cavity (no relubrication path)
- edge loading from shaft deflection or housing misalignment
- rolling-contact fatigue spalling after the rated L10 life is exceeded
Selection pitfalls — read before you substitute
- Temperature rise and interference fits consume internal clearance on this 60 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 61912 with C3 for those conditions.
- The 619xx thin section (12.5 mm section height at 60 mm bore) trades load capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.
- Contact seals add drag and heat: 61912-2RS runs slower and cooler-limited than the open 61912; rubber lips are generally limited to roughly 80–110 °C continuous depending on grease, and C3 clearance is the common hot-duty choice.
- Never wash a sealed 61912-2RS in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
- Do not quieten a noisy bearing by preloading it: the 61900-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
- SKF catalogues the contact-sealed version as 61912-2RS1 (older printings may read -2RS1); it is shipped pre-greased and its 4500 r/min limiting speed is set by seal-lip drag and grease life versus the open bearing's 16000 r/min thermal reference speed.
- The 16.5/12 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 61912-2RS bearing?
A 61912-2RS deep-groove ball bearing has a 60 mm bore, 85 mm outer diameter and 13 mm width (2.362 × 3.346 × 0.512 in), per ISO 15 boundary dimensions. It is fitted with two contact rubber seals and is normally pre-greased.
How does the 61912 bore code work?
The last two digits of 61912 are bore code 12, giving 12 × 5 = 60 mm bore. The 85 mm outside diameter and 13 mm width follow the ISO 15 diameter series, not the bore code alone.
What does the 2RS suffix on 61912-2RS mean?
2RS means two contact elastomer seals, one each side, usually over a lifetime grease fill. Sealing against dust and moisture is better than ZZ shields, but the lip drag lowers the speed and temperature ceiling.
How does the 61900 compare with other series at the same 60 mm bore?
619 is a thin section one step above 618: 85×13 mm with a 12.5 mm radial section at 60 mm bore; a 6212 on the same bore is substantially larger and more heavily rated.
What is the SKF designation and catalogue data for 61912-2RS?
In the SKF Rolling Bearings catalogue this size is listed as 61912-2RS1 — two contact elastomer seals over a lifetime grease fill, 60×85×13 mm per ISO 15. Quoted values: C 16.5 kN, C0 12 kN, Pu 0.6 kN, limiting speed 4500 r/min, mass 210 g. Brand suffixes (2Z, 2RSH, 2RSL) differ from the industry-neutral spelling 61912-2RS.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-24. Read our editorial & correction policy.