61914-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61914-NTN model number is decoded

In the 61900-series (diameter series 9 of ISO 15) the last two digits encode the bore: 61914 carries bore code 14 = 70 mm. Outside diameter 100 mm and width 16 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 70 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. In the NTN catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (shields), LLB/LLF (non-contact seals), LLH (low-torque contact seal) and LLU (contact seal).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Temperature rise and interference fits consume internal clearance on this 70 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 61914 with C3 for those conditions.
• The 619xx thin section (15.0 mm section height at 70 mm bore) trades load capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.
• The open 61914-NTN has no lubricant retention: grease escapes and contaminants migrate straight into the 70×100×16 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Open bearings tolerate the highest speeds in the 61900-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 61914 units.
• Grease compatibility is not guaranteed between fills: mixing lithium and polyurea thickeners in a 61900-series position can soften the mixture and leak — clean out the old fill before switching grease types.
• Never mix components between two 61914-NTN units: rings, cage and balls are factory-matched and are not field-interchangeable, even between identical designations.
• The open 61914 has no integral sealing; in the NTN 2203 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), LLB/LLF (non-contact rubber seals), LLU (contact rubber seals) and LLH (a low-torque contact seal with higher speed capability than LLU). A JR or JRX suffix (printed for some thin-section sizes) denotes a pressed-steel cage, not a seal.
• At 70 mm bore 61914 is in NTN's upper general-purpose range; the pressed-steel cage is standard but mid-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NTN channel if the application sees impact loads.
• At 6500 r/min the grease limiting speed for 61914 covers medium-duty industrial drives; the open or shielded execution can run continuously at this speed with standard lithium-soap grease.
• At 26.3 kN dynamic load rating (C) and 21.2 kN static (C0), 1.45 kN fatigue load limit Cu, 61914 is a medium-load bearing suitable for most electric-motor and pump duty; the C0/C0r ratio matters for preloaded or thrust-loaded arrangements, so confirm the static safety factor with the NTN catalogue.
• At 334 g, 61914 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 70×100×16 mm envelope of 61914 gives a D/d ratio of 1.43 and 15.0 mm radial section height — this thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 26.3/21.2 kN load ratings, 1.45 kN fatigue load limit Cu NTN lists the grease limiting speed at 6500 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 334 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6914 on the 70×100×16 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61914 in a rated drive.
• Two NTN bearings of the same designation from different production lots can carry minor internal-geometry revisions; for paired or preloaded arrangements on one shaft, order a single lot through the NTN distributor.
• Order the C3 internal-clearance version (61914 with C3 after the seal code) when the shaft fit is tight or the shaft-to-housing temperature gradient exceeds roughly 10 °C — the residual clearance after mounting, not the catalogue CN figure, decides service life.