6211-RSR bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6211-RSR model number is decoded

6211-RSR uses two non-contact elastomer lips with very low drag; coarse debris stays out, but the bearing is not liquid-tight. Within the light 62xx section (diameter series 2 of ISO 15), multiplying bore code 11 by five gives the 55 mm bore; the 100 mm outside diameter and 21 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 55 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NSK's non-contact seal suffix is VV (catalogue number 6211VV), mapped here from the industry-neutral -RSR spelling; speed capability is close to the open bearing but VV is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Interference on a 55 mm shaft plus running heat consumes radial clearance: where the shaft runs hot or the fit is tight, order 6211 with C3 clearance and re-check the residual value after mounting.
• At 55 mm bore the 62xx light series is the workhorse section; its 100×21 mm envelope is what most motor and gearbox seats are machined for, so any alternative section must be checked against both this OD and this width, not the bore alone.
• The low-drag lip of 6211-RSR barely touches the inner ring; after long shelf storage the grease can separate, so rotate the rings by hand and confirm smooth, silent running before fitting.
• The non-contact lip of 6211-RSR does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 55 mm bore position before relying on it as sealed-for-life.
• Deep-groove ball bearings tolerate only minutes of misalignment; if the 100 mm housing cannot be aligned, switch to a self-aligning type rather than shimming 6211-RSR.
• The housing bore for the 100 mm OD should be round within IT7; an oval bore pinches the outer ring of 6211-RSR and shows up later as two-point loaded raceway wear.
• NSK catalogues this low-friction non-contact seal as 6211VV (suffix VV), mapped here from the industry-neutral -RSR spelling. NSK rates its speed capability close to the open bearing, but VV is not liquid-tight — for wet or fine-dust duty step up to the DDU contact seal (industry-neutral -2RS).
• At 55 mm bore 6211 is in NSK's upper general-purpose range; the pressed-steel cage is standard, but mid-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NSK channel if the application sees impact loads.
• NSK rates 6211 at 47.5 kN dynamic (C) and 29.3 kN static (C0); this upper-medium rating covers conveyor and gearbox drives, but at these loads the pressed-steel cage can be the limiting factor under shock — consider the machined brass cage (suffix M) for impact duty.
• At 619 g, 6211 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 55×100×21 mm envelope of 6211 gives a D/d ratio of 1.82 and 22.5 mm radial section height — a standard NSK medium section that balances load capacity and speed; for this geometry the pressed-steel cage is adequate up to NSK's listed speed ratings, and C3 clearance is the common choice for hot shafts.
• The 47.5/29.3 kN load ratings, mass 619 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6211VV on the 55×100×21 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6211 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK supplies its sealed units pre-greased for general duty between roughly -10 and +110 °C; low-temperature, food-grade and high-temperature fills are special executions — ask at order time, because DDU/VV units are not designed to be opened and repacked.
• NSK does not recommend washing new shielded or sealed bearings; the rust-preventive film on open units is compatible with standard lithium greases and needs no removal unless the application demands a special fill.