6211-2RS-FAG bearing: complete specifications & equivalents

Specification table

Source: catalog reference (HR 1 Rolling Bearings (Jan 2020)) · extracted 2026-09-25

Parameters extracted from the official FAG Rolling Bearings catalogue (HR 1 Rolling Bearings (Jan 2020)); FAG® is a trademark of Schaeffler Technologies AG & Co. KG, used here for identification only — mpnbase is not an authorized FAG/Schaeffler distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at schaeffler.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6211-2RS-FAG model number is decoded

In the 6200-series (diameter series 2 of ISO 15) the last two digits encode the bore: 6211 carries bore code 11 = 55 mm. Outside diameter 100 mm and width 21 mm come from the ISO 15 boundary-dimensions general plan. Suffix -2RS denotes two contact-type elastomer seals over a lifetime grease fill; the sealing lips add drag compared with open or shielded versions. For normal-load mounting with a rotating inner ring on a 55 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. Schaeffler HR 1 catalogues the lip-contact sealed version as 6211-C-2HRS (FAG suffix 2RSR), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At 55 mm bore, induction heating to roughly 80–100 °C is the clean mounting method; never exceed 120 °C, and hold 6211 against the shaft shoulder while it cools so the ring cannot creep back.
• The 62xx light series is the default general-purpose section at 55 mm bore; before upgrading to a 6311 for extra capacity, confirm the housing accepts a 100 mm OD and 21 mm width — it is not a drop-in swap.
• Heat is the enemy of the sealed 6211-2RS: sustained running near the lip temperature limit hardens the rubber, after which grease escapes and dirt tracks in — watch the housing temperature in hot drives.
• Never wash a sealed 6211-2RS-FAG in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
• Vibration during standstill brinells the raceways of a 55 mm bearing at ball spacing; if the machine sits idle next to running equipment, turn the shaft over periodically or isolate the arrangement.
• Suffixes stack in a defined order — clearance follows the seal code, e.g. 6211-2RS-FAG-C3. No clearance suffix means normal CN clearance.
• Schaeffler HR 1 lists the lip-contact sealed version as 6211-C-2HRS (FAG suffix 2RSR), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing. FAG's RSR lip material is NBR as standard — above roughly 100 °C continuous, consult Schaeffler for higher-temperature seal options.
• At 5800 r/min mechanical limiting speed, 6211 covers medium-duty industrial drives; the 2RSR lip-contact seal is the practical speed limiter — for continuous operation near the ceiling use the open or 2RZ variant with external housing sealing.
• At 55 mm bore 6211 is in Schaeffler's upper general-purpose range; the pressed steel cage is standard but mid-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for shock or very-low-speed duty — confirm cage material with the Schaeffler channel if the application sees impact loads.
• FAG rates 6211 at 46.5 kN dynamic (C) and 29 kN static (C0); this upper-medium rating covers conveyor and gearbox drives, but under shock the pressed steel cage can become the limiting element — consider the machined brass cage (suffix M) for impact duty.
• At 600 g, 6211 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 55×100×21 mm envelope of 6211 gives a D/d ratio of 1.82 and 22.5 mm radial section height — a standard FAG medium section balancing load capacity and speed; the standard cage is adequate up to the listed speeds and C3 clearance is the common hot-shaft choice.
• The 46.5/29 kN load ratings, mass 600 g here are Schaeffler HR 1 Rolling Bearings (Jan 2020) catalogue figures for 6211-C-2HRS on the 55×100×21 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6211 in a rated drive. Where FAG has since released an X-life version of this size, its expanded C/C0 ratings supersede the HR 1 print values quoted here.
• Schaeffler has moved many HR 1 sizes to the X-life generation with higher C/C0 ratings; the designation is unchanged, so a current eKatalog listing for 6211 may quote higher values than the HR 1 print figures on this page — the envelope is identical either way.
• Schaeffler's medias/eKatalog is the live source for the current execution of 6211: cage material, seal lip design and ratings can be revised between catalogue generations without any designation change.