211 bearing: complete specifications & equivalents
The 211 is a ISO 15 radial bearing sized 55 x 100 x 21 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 55 mm |
| Outer diameter D | 100 mm |
| Width B | 21 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 48.4 kN |
| Basic static load rating C0 | 44 kN |
| Fatigue load limit Pu | 1.86 kN |
| Reference speed (thermal) | 12000 rpm |
| Limiting speed (mechanical) | 7000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 660 g |
| Manufacturer designation | 211 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 200-series range
| Bore d | 2.165 in |
|---|---|
| Outer diameter D | 3.937 in |
| Width B | 0.827 in |
| ISO bore code | 11 |
| Radial section height (D−d)/2 | 22.5 mm |
| Smallest bore in 200-series | 30 mm |
| Largest outer diameter in 200-series | 180 mm |
| Width range across 200-series | 16–34 mm |
| Bore position in 200-series (smallest first) | 6 of 15 |
| Bore above smallest 200-series size | 25 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 6211-RSR | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | NSK bearing NSK 6211VV on the same 55×100×21 mm envelope, but catalogue C/C0 differ (48.4/44 kN vs 47.5/29.3 kN) — envelope interchange only after a load check. |
| 6211-M | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 55×100×21 mm envelope as SKF 6211 M, but catalogue C/C0 differ (48.4/44 kN vs 46.2/29 kN) — envelope match only after a load check. |
| 211-ZZ | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 55×100×21 mm envelope and equivalent catalogue ratings; 211-2Z is the two non-contact shields execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
| 6211 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF SKF 6211 shares the 55×100×21 mm envelope but catalogue C/C0 differ (48.4/44 kN vs 46.2/29 kN) — envelope match, not a load-rating equivalent. |
| 6211-ZZ | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF SKF 6211-2Z shares the 55×100×21 mm envelope but catalogue C/C0 differ (48.4/44 kN vs 46.2/29 kN) — envelope match, not a load-rating equivalent. |
| 6211-2RS | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF SKF 6211-2RSH shares the 55×100×21 mm envelope but catalogue C/C0 differ (48.4/44 kN vs 46.2/29 kN) — envelope match, not a load-rating equivalent. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 211 model number is decoded
211 is a filling-slot (notched-ring) deep-groove bearing in the legacy 200-series: the last two digits encode the bore: 211 carries code 11 = 55 mm (code × 5). The rings carry loading slots that allow extra balls during assembly, which is what gives the 55×100×21 mm envelope its C 48.4 kN and C0 44 kN ratings (Pu 1.86 kN). The open 211 carries no shields or seals and relies on application lubrication and external sealing. Limiting speed 7000 r/min, mass 660 g. These bearings are built for high purely-radial loads at moderate speeds.
Typical equipment & failure modes
Common applications
- construction equipment drives
- hoists and winch gear trains
- eccentric and vibratory conveyors
- legacy machinery repairs
Known failure patterns
- spalling of the filling-slot edge when balls are hammered through the slot under heavy thrust loading
- dirt entering through the open slot area when external sealing is neglected
- brinelling from static overload or hammer blows during mounting
- false brinelling from vibration while the shaft stands idle
Selection pitfalls — read before you substitute
- The slots sit at one angular position: on 211, never pass the full radial load across the slot zone during mounting or the ring lip can crack.
- 211 uses the legacy SKF 200/300 numbering (light/heavy filling-slot series), not the modern 6200/6300 spelling; quote 211 exactly when ordering replacements.
- Filling-slot bearings take heavy purely-radial load at moderate speed but little thrust; the 48.4/44 kN ratings assume radial loading — use deep-groove 6xxx where axial load matters.
- Shields on 211 retain grease but do not seal against water; for wet farm duty add external lip seals rather than trusting the shield.
- Filling-slot bearings take heavy purely-radial load at moderate speed but little thrust; the 48.4/44 kN ratings assume radial loading — use deep-groove 6xxx where axial load matters.
- The fatigue load limit is 1.86 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
Frequently asked questions
What are the dimensions of 211?
Filling-slot bearing 211 measures 55×100×21 mm (2.165×3.937×0.827 in), about 660 g.
What does the designation 211 mean?
It is the legacy 200/300 filling-slot numbering: series 200 and bore code 11 = 55 mm. Filling-slot bearings predate the 6xxx deep-groove spelling.
Can 211 take axial load?
Very little: the filling slots interrupt the raceway shoulders, so thrust towards the open slot side can unload or jam the balls. Use a standard deep-groove 6xxx bearing for combined loads.
Why use an old 200-series bearing instead of a 62xx?
For slow, heavy, purely-radial duty the extra balls give more capacity in the same bore, and the separable rings simplify assembly in blind housings; at high speed modern designs run better.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.