6212-RSR-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6212-RSR-NTN model number is decoded

6212-RSR uses two non-contact elastomer lips with very low drag; coarse debris stays out, but the bearing is not liquid-tight. Within the light 62xx section (diameter series 2 of ISO 15), multiplying bore code 12 by five gives the 60 mm bore; the 110 mm outside diameter and 22 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 60 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NTN's non-contact seal suffix is LLB/LLF (catalogue number 6212LLB), mapped here from the industry-neutral -RSR spelling; speed capability matches the open bearing but it is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Interference on a 60 mm shaft plus running heat consumes radial clearance: where the shaft runs hot or the fit is tight, order 6212 with C3 clearance and re-check the residual value after mounting.
• At 60 mm bore the 62xx light series is the workhorse section; its 110×22 mm envelope is what most motor and gearbox seats are machined for, so any alternative section must be checked against both this OD and this width, not the bore alone.
• RSR low-friction seals on 6212-RSR-NTN run faster than contact-seal 6212-2RS but let fine dust and moisture past the non-contact lip; in dirty or wet duty specify 6212-2RS instead.
• The non-contact lip of 6212-RSR-NTN does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 60 mm bore position before relying on it as sealed-for-life.
• The housing bore for the 110 mm OD should be round within IT7; an oval bore pinches the outer ring of 6212-RSR-NTN and shows up later as two-point loaded raceway wear.
• Do not quieten a noisy bearing by preloading it: the 6200-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• NTN catalogues this low-friction non-contact seal as 6212LLB (suffix LLB), mapped here from the industry-neutral -RSR spelling. NTN rates its speed capability the same as the open bearing, but it is not liquid-tight — for wet or fine-dust duty step up to the LLU contact seal (industry-neutral -2RS).
• At 60 mm bore 6212 is in NTN's upper general-purpose range; the pressed-steel cage is standard but mid-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NTN channel if the application sees impact loads.
• NTN lists the grease limiting speed at 4500 r/min for 6212; this is a large or heavy-section size where centrifugal force and cage inertia cap the speed — for higher shaft speeds either step to a smaller bearing on the same bore or consult NTN for an oil-lubricated, machined-cage variant.
• NTN rates 6212 at 58 kN dynamic (C) and 36 kN static (C0), 2.83 kN fatigue load limit Cu; this upper-medium rating covers conveyor and gearbox drives, but at these loads the pressed-steel cage can be the limiting factor under shock — consider the machined brass cage (suffix M) for impact duty.
• At 783 g, 6212 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 60×110×22 mm envelope of 6212 gives a D/d ratio of 1.83 and 25.0 mm radial section height — a standard medium section that balances load capacity and speed; for this geometry the pressed-steel cage is adequate up to the listed limiting speed, and C3 clearance is the common choice for hot shafts.
• The 58/36 kN load ratings, 2.83 kN fatigue load limit Cu NTN lists the grease limiting speed at 4500 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 783 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6212LLB on the 60×110×22 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6212 in a rated drive.
• Standard catalogue stock of 6212 is the general-purpose execution; for low-noise motor duty NTN offers low-torque seal and special-grease variants in this size class, which are separate order numbers.
• Two NTN bearings of the same designation from different production lots can carry minor internal-geometry revisions; for paired or preloaded arrangements on one shaft, order a single lot through the NTN distributor.