MPNbase

60×110×22 mm bearings

48 models from 3 brands across 6 types share this ISO 15 envelope: 60 mm bore, 110 mm outside diameter, 22 mm width (2.362×4.331×0.866 in), 25 mm radial section.

48 models fit this space 3 brands 48 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
11212-TN9 Self-Aligning Ball SKF open CN 31.2 12.2 1150
1212 Self-Aligning Ball NTN open — 30.5 11.5 910
1212-EKTN9 Self-Aligning Ball SKF open CN 31.2 12.2 900
1212-ETN9 Self-Aligning Ball SKF open CN 31.2 12.2 900
1212K Self-Aligning Ball NTN open — 30.5 11.5 910
1726212-2RS1 Insert (Y-bearings) SKF 2RS CN 52.7 36 770
212 Deep Groove Ball SKF open CN 56.1 50 850
212-ZZ Deep Groove Ball SKF ZZ CN 56.1 50 850
397-394A Tapered Roller NTN open CN 99.5 120 918
6212 Deep Groove Ball SKF open CN 55.3 36 780
6212-2RS Deep Groove Ball SKF 2RS CN 55.3 36 790
6212-2RS-NSK Deep Groove Ball NSK 2RS CN 57.5 36 783
6212-2RS-NTN Deep Groove Ball NTN 2RS CN 58 36 783
6212-M Deep Groove Ball SKF open CN 55.3 36 930
6212-NSK Deep Groove Ball NSK open CN 57.5 36 783
6212-NTN Deep Groove Ball NTN open CN 58 36 783
6212-RSR Deep Groove Ball NSK RSR CN 57.5 36 783
6212-RSR-NTN Deep Groove Ball NTN RSR CN 58 36 783
6212-ZZ Deep Groove Ball SKF ZZ CN 55.3 36 810
6212-ZZ-NSK Deep Groove Ball NSK ZZ CN 57.5 36 783
6212-ZZ-NTN Deep Groove Ball NTN ZZ CN 58 36 783
7212 Angular Contact Ball SKF open CN 57.2 45.5 800
7212-ACCBM Angular Contact Ball SKF open CN 69.5 56 800
7212-BECBM Angular Contact Ball SKF open CN 61 50 800
7212-BECBP Angular Contact Ball SKF open CN 61 50 800
7212-BECBPH Angular Contact Ball SKF open CN 61 50 800
7212-BECBY Angular Contact Ball SKF open CN 61 50 800
7212-BEP Angular Contact Ball SKF open CN 57.2 45.5 800
7212-NTN Angular Contact Ball NTN open CN 68.5 49 765
7212B Angular Contact Ball NTN open CN 62 44.5 780
N212 Cylindrical Roller NTN open CN 76 75 802
N212-ECP Cylindrical Roller SKF open CN 108 102 790
N212EA Cylindrical Roller NTN open CN 115 107 798
NF212 Cylindrical Roller NTN open CN 76 75 802
NF212EA Cylindrical Roller NTN open CN 115 107 798
NJ212 Cylindrical Roller NTN open CN 76 75 802
NJ212-ECP Cylindrical Roller SKF open CN 108 102 820
NJ212EA Cylindrical Roller NTN open CN 115 107 798
NU212 Cylindrical Roller SKF open CN 108 102 800
NU212-NTN Cylindrical Roller NTN open CN 76 75 802
NU212EA Cylindrical Roller NTN open CN 115 107 798
NUP212 Cylindrical Roller NTN open CN 76 75 802
NUP212-ECP Cylindrical Roller SKF open CN 108 102 860
NUP212EA Cylindrical Roller NTN open CN 115 107 798
QJ-212-MA Angular Contact Ball SKF open CN 96.5 93 990
QJ-212-N2MA Angular Contact Ball SKF open CN 96.5 93 990
QJ-212-N2PHAS Angular Contact Ball SKF open CN 96.5 93 990
QJ212 Angular Contact Ball NTN open CN 86 138 980

Note: catalogue dynamic load ratings for this envelope span 30.5– 115.0 kN — a 277% spread between designs in the very same 60×110×22 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 60 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 11212-TN9, 1212, 1212-EKTN9, 1212-ETN9, 1212K, 1726212-2RS1, 212, 212-ZZ, 397-394A, 6212, 6212-2RS, 6212-2RS-NSK, 6212-2RS-NTN, 6212-M, 6212-NSK, 6212-NTN, 6212-RSR, 6212-RSR-NTN, 6212-ZZ, 6212-ZZ-NSK, 6212-ZZ-NTN, 7212, 7212-ACCBM, 7212-BECBM, 7212-BECBP, 7212-BECBPH, 7212-BECBY, 7212-BEP, 7212-NTN, 7212B, N212, N212-ECP, N212EA, NF212, NF212EA, NJ212, NJ212-ECP, NJ212EA, NU212, NU212-NTN, NU212EA, NUP212, NUP212-ECP, NUP212EA, QJ-212-MA, QJ-212-N2MA, QJ-212-N2PHAS, QJ212.

Frequently asked questions

Are all 60×110×22 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 60 mm bore, 110 mm OD, 22 mm width (2.362×4.331×0.866 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 48 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 60×110×22?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 60×110×22 mm in inches?

60×110×22 mm converts to 2.362×4.331×0.866 in, with a 25 mm (0.984 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 11212-TN9, 1212, 1212-EKTN9 mount in the same space despite different internal designs.