7212-BECBPH bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 7212-BECBPH model number is decoded

7212 BECBPH is SKF's 60 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 60×110×22 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable. Envelope 60×110×22 mm (2.362×4.331×0.866 in), 25.0 mm radial section height, C 61 kN, C0 50 kN, Pu 2.12 kN.reference speed 7,000 r/min (thermal) and limiting speed 7,500 r/min (mechanical), catalogue mass 800 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 7,500 r/min while thermal balance under catalogue load sets the 7,000 r/min reference; at dm ≈ 85.0 mm the corresponding dn is approximately 638k mm·r/min. At the printed limiting speed of 7,500 r/min the mean pitch diameter dm ≈ 85.0 mm implies a dn value around 638k mm·r/min; the 7,000 r/min reference speed is the thermal-planning figure under catalogue load. Speed-ratio note for this exact unit: the reference speed is 7,000 r/min against a 7,500 r/min limiting speed, i.e. a reference-to-limit ratio of 0.93. PEEK cage note: the PH cage is moulded from glass-fibre reinforced polyetheretherketone, ball-centred, aimed at high-speed oil-air and grease positions where PA66 would approach its thermal and speed limits; it needs clean lubricant (PEEK cages are sensitive to hard-particle cage-wear) and is a separate order number from the brass BECBM.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.
• DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.
• Assign interference to the rotating ring — roughly k5 on a 60 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.
• Fillet radii must clear the chamfer so the 22 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
• The steep 40° angle of 7212-BECBPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.
• Universally matchable BECBPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure.