7212-BEP bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 7212-BEP model number is decoded

7212 BEP is SKF's 60 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 60×110×22 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 60×110×22 mm (2.362×4.331×0.866 in), 25.0 mm radial section height, C 57.2 kN, C0 45.5 kN, Pu 1.93 kN.reference speed 7,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical), which coincide for this size, catalogue mass 800 g. At the printed limiting speed of 7,000 r/min the mean pitch diameter dm ≈ 85.0 mm implies a dn value around 595k mm·r/min; the 7,000 r/min reference speed is the thermal-planning figure under catalogue load. The 1.93 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 57.2/45.5 kN ratings and 800 g mass this execution carries about 0.95 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 7,000 r/min against a 7,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.
• Preload the set against a calculated stand-off dimension — the ground faces of BEP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.
• Greased positions should fill roughly 25–35 % of the free volume on a 7212-BEP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.
• Assign interference to the rotating ring — roughly k5 on a 60 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.
• The steep 40° angle of 7212-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.
• Catalogue ratings are SKF PUB BU/P1 17000 figures for 7212 BEP as the single basic pa66 execution; the other order numbers of the 7212 size are different products and may carry different ratings — always quote the full designation when purchasing.