QJ-212-MA bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the QJ-212-MA model number is decoded

QJ 212 MA is SKF's 60 mm-bore QJ four-point contact ball bearing of the QJ200 series, 60×110×22 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 60×110×22 mm (2.362×4.331×0.866 in), 25.0 mm radial section height, C 96.5 kN, C0 93 kN, Pu 4 kN.SKF publishes only the 10,000 r/min limiting speed for this execution, catalogue mass 990 g. Sizing arithmetic on the 60 mm bore: 96.5 kN C divided by the 25.0 mm radial section height gives 3.9 kN per section millimetre; the 990 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. The 4 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 96.5/93 kN ratings and 990 g mass this execution carries about 1.61 kN of C per millimetre of bore. Bore-to-OD planning: OD 110 over bore 60 is a 1.83× step for this size, and the 22 mm width gives a bore/width ratio of 2.73; use these ratios when housing space around the 60 mm shaft is the first constraint. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing
• The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.
• Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.
• Anti-rotation is NOT built into QJ-212-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.
• The MA brass cage of QJ-212-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.
• Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 212 MA as the qj plain execution; the other order numbers of the QJ 212 size are different products and may carry different ratings — always quote the full designation when purchasing.