1212-ETN9 bearing: complete specifications & equivalents
The 1212-ETN9 is a ISO 15 radial bearing sized 60 x 110 x 22 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 60 mm |
| Outer diameter D | 110 mm |
| Width B | 22 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | polymer (PA66 glass-fibre reinforced) |
| Basic dynamic load rating C | 31.2 kN |
| Basic static load rating C0 | 12.2 kN |
| Fatigue load limit Pu | 0.62 kN |
| Reference speed (thermal) | 12000 rpm |
| Limiting speed (mechanical) | 8500 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 900 g |
| Manufacturer designation | 1212 ETN9 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 1200-series range
| Bore d | 2.362 in |
|---|---|
| Outer diameter D | 4.331 in |
| Width B | 0.866 in |
| ISO bore code | 12 |
| Radial section height (D−d)/2 | 25 mm |
| Smallest bore in 1200-series | 6 mm |
| Largest outer diameter in 1200-series | 230 mm |
| Width range across 1200-series | 6–154 mm |
| Bore position in 1200-series (smallest first) | 18 of 32 |
| Bore above smallest 1200-series size | 54 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 1212 | NTN | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 1212-EKTN9 | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 60×110×22 mm envelope with catalogue ratings within 10 %; 1212 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs. |
| 11212-TN9 | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 60×110×22 mm envelope with catalogue ratings within 10 %; 11212 TN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 1212-ETN9 model number is decoded
The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1212 carries code 12 = 60 mm (code × 5). Envelope 60×110×22 mm (2.362×4.331×0.866 in) with a 25.0 mm radial section height, C 31.2 kN, C0 12.2 kN and Pu 0.62 kN. The open 1212 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 60 mm shaft. Reference (thermal) speed 12000 r/min, limiting speed 8500 r/min, catalogue mass 900 g.
Typical equipment & failure modes
Common applications
- woodworking machinery
- pump shafts with mild misalignment
- material-handling equipment
- industrial electric motors
Known failure patterns
- contamination wear when the open arrangement is used without adequate external sealing
- lubricant starvation where no regreasing interval is maintained
- raceway smearing under marginal lubrication at start-up
- electrical pitting in VFD-driven motors without shaft grounding
Selection pitfalls — read before you substitute
- Catalogue ratings for 1212-ETN9 (C 31.2 kN, C0 12.2 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
- Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1212-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.
- The ETN9 suffix on 1212-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 8500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.
- Fillet radii must clear the 1212-ETN9 chamfer so the 22 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
- Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1212-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.
- Assign interference to the rotating ring: on a 60 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.
Frequently asked questions
What are the dimensions of 1212-ETN9?
SKF 1212 ETN9 measures 60 mm bore × 110 mm OD × 22 mm width (2.362 × 4.331 × 0.866 in), mass about 900 g. It is open, with no shields or seals.
How does the bore code in 1212 work?
The final two digits of 1212 are bore code 12, multiplied by 5 to give 60 mm.
How heavy is 1212-ETN9?
Catalogue mass is 900 g for 1212 ETN9; seal and cage executions of the same envelope differ by a few grams.
What load can 1212-ETN9 take?
Catalogue values for 1212 ETN9: dynamic C 31.2 kN, static C0 12.2 kN, fatigue limit Pu 0.62 kN. Use C in life calculation and C0 for static checks at 60 mm bore.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.