6217-ZZ-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6217-ZZ-NTN model number is decoded

6217-ZZ carries two non-contact sheet-steel shields that hold the factory grease in and keep coarse debris out; they do not seal against liquids. Within the light 62xx section (diameter series 2 of ISO 15), multiplying bore code 17 by five gives the 85 mm bore; the 150 mm outside diameter and 28 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 85 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NTN catalogue order number: 6217ZZ (suffix ZZ), two non-contact steel shields, mapped here from the industry-neutral -ZZ spelling.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Large bores like the 85 mm of 6217-ZZ-NTN demand clean, burr-free seats; one raised burr under a ring this size cocks the bearing and concentrates load at the raceway edge, cutting life drastically.
• The 62xx light series is the default general-purpose section at 85 mm bore; before upgrading to a 6317 for extra capacity, confirm the housing accepts a 150 mm OD and 28 mm width — it is not a drop-in swap.
• ZZ shields are non-contact: 6217-ZZ-NTN blocks chips and coarse dust but is not waterproof — do not install it expecting a pressure-wash seal, step up to 6217-2RS for that.
• Shielded 6217-ZZ-NTN units are typically greased for life; prying the shields out for regreasing usually bends them and leaves a gap that throws grease in service.
• The housing bore for the 150 mm OD should be round within IT7; an oval bore pinches the outer ring of 6217-ZZ-NTN and shows up later as two-point loaded raceway wear.
• Shaft and housing fillets must clear the bearing chamfer so the 28 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.
• NTN catalogues the shielded version as 6217ZZ — suffix ZZ, two non-contact steel shields. The industry-neutral page spelling is -ZZ; quote the NTN order number when buying through an NTN channel.
• At 85 mm bore 6217 is in NTN's medium industrial range; the pressed-steel cage is standard but large-section 63xx/64xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NTN channel if the application sees impact loads.
• NTN lists the grease limiting speed at 4200 r/min for 6217; this is a large or heavy-section size where centrifugal force and cage inertia cap the speed — for higher shaft speeds either step to a smaller bearing on the same bore or consult NTN for an oil-lubricated, machined-cage variant.
• At 92 kN dynamic load rating (C) and 64 kN static (C0), 4.6 kN fatigue load limit Cu, 6217 is a heavy-load bearing for industrial gearboxes and large conveyors; NTN expects a machined brass cage (suffix M) at this rating for shock duty, and the static C0 must be checked against any mounting or lifting loads.
• At 1790 g (1.8 kg), 6217 needs mechanical handling for mounting; NTN recommends induction heating the inner ring (max 120 °C) rather than pressing cold, and a lifting eye if the housing is pre-assembled.
• The 85×150×28 mm envelope of 6217 gives a D/d ratio of 1.76 and 32.5 mm radial section height — a standard medium section that balances load capacity and speed; for this geometry the pressed-steel cage is adequate up to the listed limiting speed, and C3 clearance is the common choice for hot shafts.
• The 92/64 kN load ratings, 4.6 kN fatigue load limit Cu NTN lists the grease limiting speed at 4200 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 1790 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6217ZZ on the 85×150×28 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6217 in a rated drive.
• Two NTN bearings of the same designation from different production lots can carry minor internal-geometry revisions; for paired or preloaded arrangements on one shaft, order a single lot through the NTN distributor.
• Order the C3 internal-clearance version (6217 with C3 after the seal code) when the shaft fit is tight or the shaft-to-housing temperature gradient exceeds roughly 10 °C — the residual clearance after mounting, not the catalogue CN figure, decides service life.