6217 bearing: complete specifications & equivalents
The 6217 is a ISO 15 radial bearing sized 85 x 150 x 28 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Bore diameter d | 85 mm |
| Outer diameter D | 150 mm |
| Width B | 28 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 87.1 kN |
| Basic static load rating C0 | 64 kN |
| Fatigue load limit Pu | 2.5 kN |
| Reference speed (thermal) | 9000 rpm |
| Limiting speed (mechanical) | 5600 rpm |
| Operating temperature | -40 to +150 °C |
| Mass | 1800 g |
| Manufacturer designation | SKF 6217 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-24 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 6200-series range
| Bore d | 3.346 in |
|---|---|
| Outer diameter D | 5.906 in |
| Width B | 1.102 in |
| ISO bore code | 17 |
| Radial section height (D−d)/2 | 32.5 mm |
| Smallest bore in 6200-series | 10 mm |
| Largest outer diameter in 6200-series | 400 mm |
| Width range across 6200-series | 9–65 mm |
| Bore position in 6200-series (smallest first) | 18 of 33 |
| Bore above smallest 6200-series size | 75 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 6217 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 6217 model number is decoded
In the 6200-series (ISO 15 diameter series 2) the last two digits encode the bore: 6217 carries bore code 17 = 85 mm. Outside diameter 150 mm and width 28 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 85 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. In the SKF catalogue this open execution carries the bare designation; protected variants are ordered separately as -2Z and -2RSH.
Typical equipment & failure modes
Common applications
- large gearboxes
- industrial fans and blowers
- hoists and winches
- heavy conveyors
Known failure patterns
- contamination wear from dust and dirt ingress through the open arrangement
- lubricant starvation when no regreasing interval is maintained
- false brinelling from vibration while the shaft is stationary
- fretting corrosion on a loose shaft seat
Selection pitfalls — read before you substitute
- Mount this 85 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
- The 62xx light series is the default general-purpose section at 85 mm bore; before upgrading to a 6317 for extra capacity, confirm the housing accepts a 150 mm OD and 28 mm width — it is not a drop-in swap.
- The open 6217 has no lubricant retention: grease escapes and contaminants migrate straight into the 85×150×28 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
- Open bearings tolerate the highest speeds in the 6200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 6217 units.
- Shaft and housing fillets must clear the bearing chamfer so the 28 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.
- The open 6217 needs external sealing and application-supplied lubrication; in the SKF catalogue the protected variants are separate order numbers 6217-2Z (shields) and 6217-2RSH (contact seals), not suffix-free 6217.
- The 87.1/64 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 6217 bearing?
A 6217 deep-groove ball bearing has a 85 mm bore, 150 mm outer diameter and 28 mm width (3.346 × 5.906 × 1.102 in), per ISO 15 boundary dimensions. It is an open bearing with no seals or shields. Geometry-based estimated mass is about 1714 g for a steel-cage unit; catalogue masses vary slightly with seal and cage design.
How does the 6217 bore code work?
The last two digits of 6217 are bore code 17, giving 17 × 5 = 85 mm bore. The 150 mm outside diameter and 28 mm width follow the ISO 15 diameter series, not the bore code alone.
What does no suffix on 6217 mean?
A bare 6217 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication.
How does the 6200 compare with other series at the same 85 mm bore?
The '2' is the light diameter series: 150×28 mm with a 32.5 mm radial section at 85 mm bore. A 6317 on the same bore is larger and higher-rated; a 6017 is smaller and lower-rated.
What is the SKF designation and catalogue data for 6217?
In the SKF Rolling Bearings catalogue this size is listed as 6217 — the open (unsealed) execution, 85×150×28 mm per ISO 15. Quoted values: C 87.1 kN, C0 64 kN, Pu 2.5 kN, limiting speed 5600 r/min, mass 1800 g. Brand suffixes (2Z, 2RSH) differ from the industry-neutral spelling 6217.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-24. Read our editorial & correction policy.