6226-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6226-NTN model number is decoded

6226 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the light 62xx section (diameter series 2 of ISO 15), multiplying bore code 26 by five gives the 130 mm bore; the 230 mm outside diameter and 40 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 130 mm shaft under normal load, catalogue practice seats it on a m6 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the NTN catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (shields), LLB/LLF (non-contact seals), LLH (low-torque contact seal) and LLU (contact seal).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount this 130 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
• At 130 mm bore the 62xx light series is the workhorse section; its 230×40 mm envelope is what most motor and gearbox seats are machined for, so any alternative section must be checked against both this OD and this width, not the bore alone.
• The open 6226-NTN has no lubricant retention: grease escapes and contaminants migrate straight into the 130×230×40 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Open bearings tolerate the highest speeds in the 6200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 6226 units.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• Deep-groove ball bearings tolerate only minutes of misalignment; if the 230 mm housing cannot be aligned, switch to a self-aligning type rather than shimming 6226-NTN.
• The open 6226 has no integral sealing; in the NTN 2203 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), LLB/LLF (non-contact rubber seals), LLU (contact rubber seals) and LLH (a low-torque contact seal with higher speed capability than LLU). A JR or JRX suffix (printed for some thin-section sizes) denotes a pressed-steel cage, not a seal.
• The 130 mm bore places 6226 at the lower end of NTN's large-size range; at these diameters the pressed-steel cage is speed-limited and NTN commonly supplies a machined brass cage (suffix M) as an option. Verify cage material and relubrication interval with the NTN distributor, and do not extrapolate small-bore speed ratings to this size.
• NTN lists the grease limiting speed at 2700 r/min for 6226; this is a large or heavy-section size where centrifugal force and cage inertia cap the speed — for higher shaft speeds either step to a smaller bearing on the same bore or consult NTN for an oil-lubricated, machined-cage variant.
• At 185 kN dynamic load rating (C) and 146 kN static (C0), 8.55 kN fatigue load limit Cu, 6226 is a heavy-load bearing for industrial gearboxes and large conveyors; NTN expects a machined brass cage (suffix M) at this rating for shock duty, and the static C0 must be checked against any mounting or lifting loads.
• At 5820 g (5.8 kg), 6226 is a heavy bearing that requires a crane or hoist for handling; induction-heat the inner ring (max 120 °C) and use a mechanical puller for removal — never apply heat directly to the balls or cage.
• The 130×230×40 mm envelope of 6226 gives a D/d ratio of 1.77 and 50.0 mm radial section height — a standard medium section that balances load capacity and speed; for this geometry the pressed-steel cage is adequate up to the listed limiting speed, and C3 clearance is the common choice for hot shafts.
• The 185/146 kN load ratings, 8.55 kN fatigue load limit Cu NTN lists the grease limiting speed at 2700 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 5820 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6226 on the 130×230×40 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6226 in a rated drive.
• Two NTN bearings of the same designation from different production lots can carry minor internal-geometry revisions; for paired or preloaded arrangements on one shaft, order a single lot through the NTN distributor.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.