62200-2RS bearing: complete specifications & equivalents
The 62200-2RS is a ISO 15 radial bearing sized 10 x 30 x 14 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 10 mm |
| Outer diameter D | 30 mm |
| Width B | 14 mm |
| Material | GCr15 |
| Seal / shield | 2RS |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 5.07 kN |
| Basic static load rating C0 | 2.36 kN |
| Fatigue load limit Pu | 0.1 kN |
| Limiting speed (mechanical) | 17000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 40 g |
| Manufacturer designation | 62200-2RS1 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 62200-series range
| Bore d | 0.394 in |
|---|---|
| Outer diameter D | 1.181 in |
| Width B | 0.551 in |
| ISO bore code | 00 |
| Radial section height (D−d)/2 | 10 mm |
| Smallest bore in 62200-series | 10 mm |
| Largest outer diameter in 62200-series | 125 mm |
| Width range across 62200-series | 14–31 mm |
| Bore position in 62200-series (smallest first) | 1 of 15 |
| Bore above smallest 62200-series size | 0 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 4200-ATN9 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 10×30×14 mm envelope as SKF 4200 ATN9, but catalogue C/C0 differ (5.07/2.36 kN vs 9.23/5.2 kN) — envelope match only after a load check. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 62200-2RS model number is decoded
The 62200-series is the wide-section counterpart of the standard deep-groove family (extra width code built into the designation); bore code 00 follows the 10/12/15/17 mm exception table, so 62200 fits a 10 mm shaft. The envelope is 10×30×14 mm (0.394×1.181×0.551 in) with a 10.0 mm radial section height, C 5.07 kN, C0 2.36 kN and Pu 0.1 kN. SKF catalogues the sealed execution as 62200-2RS1: two contact elastomer lips (2RS1/2RSH spelling) over a lifetime grease fill; the lips add drag, and no reference (thermal) speed is published. Limiting speed 17000 r/min, catalogue mass 40 g.
Typical equipment & failure modes
Common applications
- electric motors
- centrifugal pumps
- small gearboxes
- conveyor drives
Known failure patterns
- contact-seal lip hardening and pre-grease loss after long high-temperature service
- grease-life expiry inside the sealed-for-life cavity, which has no relubrication path
- false brinelling from vibration while the shaft stands idle
- fretting corrosion on a creeping shaft or housing seat
Selection pitfalls — read before you substitute
- The fatigue load limit is 0.1 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
- The fatigue load limit is 0.1 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
- Contact seals make 62200-2RS slower than the open 62200 (limiting 17000 r/min) and forbid solvent washing, which destroys the lifetime grease.
- Do not pry the caps off 62200-2RS to repack it; shield/seal damage leaves a gap that throws grease and admits dirt.
- Clearance suffixes follow the seal code in the designation stack (e.g. 62200-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
- At 10 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.
Frequently asked questions
What are the dimensions of 62200-2RS?
The SKF 62200-2RS1 measures 10 mm bore × 30 mm OD × 14 mm width (0.394 × 1.181 × 0.551 in), mass about 40 g. It has two contact rubber seals and a lifetime grease fill.
How does the bore code in 62200 work?
Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 62200 fits a 10 mm shaft. Code × 5 starts at code 04.
How heavy is 62200-2RS?
Catalogue mass is 40 g for 62200-2RS1; seal and cage executions of the same envelope differ by a few grams.
What load can 62200-2RS take?
Catalogue values for 62200-2RS1: dynamic C 5.07 kN, static C0 2.36 kN, fatigue limit Pu 0.1 kN. Use C in life calculation and C0 for static checks at 10 mm bore.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.