62214-2RS bearing: complete specifications & equivalents
The 62214-2RS is a ISO 15 radial bearing sized 70 x 125 x 31 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 70 mm |
| Outer diameter D | 125 mm |
| Width B | 31 mm |
| Material | GCr15 |
| Seal / shield | 2RS |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 60.5 kN |
| Basic static load rating C0 | 45 kN |
| Fatigue load limit Pu | 1.9 kN |
| Limiting speed (mechanical) | 3400 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 1400 g |
| Manufacturer designation | 62214-2RS1 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 62200-series range
| Bore d | 2.756 in |
|---|---|
| Outer diameter D | 4.921 in |
| Width B | 1.22 in |
| ISO bore code | 14 |
| Radial section height (D−d)/2 | 27.5 mm |
| Smallest bore in 62200-series | 10 mm |
| Largest outer diameter in 62200-series | 125 mm |
| Width range across 62200-series | 14–31 mm |
| Bore position in 62200-series (smallest first) | 15 of 15 |
| Bore above smallest 62200-series size | 60 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 4214-ATN9 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 70×125×31 mm envelope as SKF 4214 ATN9, but catalogue C/C0 differ (60.5/45 kN vs 70.2/73.5 kN) — envelope match only after a load check. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 62214-2RS model number is decoded
The 62200-series is the wide-section counterpart of the standard deep-groove family (extra width code built into the designation); the last two digits encode the bore: 62214 carries code 14 = 70 mm (code × 5). The envelope is 70×125×31 mm (2.756×4.921×1.22 in) with a 27.5 mm radial section height, C 60.5 kN, C0 45 kN and Pu 1.9 kN. SKF catalogues the sealed execution as 62214-2RS1: two contact elastomer lips (2RS1/2RSH spelling) over a lifetime grease fill; the lips add drag, and no reference (thermal) speed is published. Limiting speed 3400 r/min, catalogue mass 1400 g.
Typical equipment & failure modes
Common applications
- gearboxes and speed reducers
- centrifugal and positive-displacement pumps
- material-handling equipment
- industrial fans
Known failure patterns
- contact-seal lip hardening and pre-grease loss after long high-temperature service
- grease-life expiry inside the sealed-for-life cavity, which has no relubrication path
- brinelling from static overload or hammer blows during mounting
- false brinelling from vibration while the shaft stands idle
Selection pitfalls — read before you substitute
- The fatigue load limit is 1.9 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
- Deep-groove geometry tolerates only minutes of misalignment; if the 125 mm housing bore cannot be aligned, move to a self-aligning bearing rather than shimming 62214-2RS.
- Contact seals make 62214-2RS slower than the open 62214 (limiting 3400 r/min) and forbid solvent washing, which destroys the lifetime grease.
- Do not pry the caps off 62214-2RS to repack it; shield/seal damage leaves a gap that throws grease and admits dirt.
- Catalogue ratings for 62214-2RS (C 60.5 kN, C0 45 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
- Mount by heating the inner ring (max 120 °C) — driving 62214-2RS home through the outer ring or balls brinells the raceways.
Frequently asked questions
What are the dimensions of 62214-2RS?
The SKF 62214-2RS1 measures 70 mm bore × 125 mm OD × 31 mm width (2.756 × 4.921 × 1.22 in), mass about 1400 g. It has two contact rubber seals and a lifetime grease fill.
How does the bore code in 62214 work?
The final two digits of 62214 are bore code 14, multiplied by 5 to give 70 mm.
What load can 62214-2RS take?
Catalogue values for 62214-2RS1: dynamic C 60.5 kN, static C0 45 kN, fatigue limit Pu 1.9 kN. Use C in life calculation and C0 for static checks at 70 mm bore.
What is the speed rating of 62214-2RS?
SKF publishes only the 3400 r/min limiting speed for this execution; sealed variants have no thermal reference speed because seal and grease life govern.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.