70×125×31 mm bearings

26 models from 3 brands across 5 types share this ISO 15 envelope: 70 mm bore, 125 mm outside diameter, 31 mm width (2.756×4.921×1.220 in), 27.5 mm radial section.

26 models fit this space 3 brands 26 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
2214 Self-Aligning Ball NTN open — 44 17.1 1550
2214-E-2RS1TN9 Self-Aligning Ball SKF 2RS CN 35.8 14.6 1450
22214 Spherical Roller SKF open CN 213 228 1550
22214-EK Spherical Roller SKF open CN 213 228 2150
22214EAD1 Spherical Roller NTN open CN 235 240 1610
22214EAKD1 Spherical Roller NTN open CN 235 240 1580
22214EMD1 Spherical Roller NTN open CN 235 240 1640
22214EMKD1 Spherical Roller NTN open CN 235 240 1600
4214-ATN9 Deep Groove Ball SKF open CN 70.2 73.5 1500
62214-2RS Deep Groove Ball SKF 2RS CN 60.5 45 1400
C2214-KTN9 CARB Toroidal Roller SKF open CN 186 196 1500
C2214-TN9 CARB Toroidal Roller SKF open CN 186 196 1500
C2214-V CARB Toroidal Roller SKF open CN 212 228 1550
N2214 Cylindrical Roller NTN open CN 132 151 1440
N2214EA Cylindrical Roller NTN open CN 184 194 1520
NF2214EA Cylindrical Roller NTN open CN 184 194 1520
NJ2214 Cylindrical Roller NTN open CN 132 151 1440
NJ2214-ECP Cylindrical Roller SKF open CN 180 193 1500
NJ2214EA Cylindrical Roller NTN open CN 184 194 1520
NU2214 Cylindrical Roller NTN open CN 132 151 1440
NU2214-ECP Cylindrical Roller SKF open CN 180 193 1500
NU2214EA Cylindrical Roller NTN open CN 184 194 1520
NUP2214 Cylindrical Roller NTN open CN 132 151 1440
NUP2214-ECP Cylindrical Roller SKF open CN 180 193 1550
NUP2214EA Cylindrical Roller NTN open CN 184 194 1520
SL182214 Cylindrical Roller FAG open CN 181 223 1660

Note: catalogue dynamic load ratings for this envelope span 35.8– 235.0 kN — a 556% spread between designs in the very same 70×125×31 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 70 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 2214, 2214-E-2RS1TN9, 22214, 22214-EK, 22214EAD1, 22214EAKD1, 22214EMD1, 22214EMKD1, 4214-ATN9, 62214-2RS, C2214-KTN9, C2214-TN9, C2214-V, N2214, N2214EA, NF2214EA, NJ2214, NJ2214-ECP, NJ2214EA, NU2214, NU2214-ECP, NU2214EA, NUP2214, NUP2214-ECP, NUP2214EA, SL182214.

Frequently asked questions

Are all 70×125×31 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 70 mm bore, 125 mm OD, 31 mm width (2.756×4.921×1.220 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 26 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 70×125×31?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 70×125×31 mm in inches?

70×125×31 mm converts to 2.756×4.921×1.220 in, with a 27.5 mm (1.083 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 2214, 2214-E-2RS1TN9, 22214 mount in the same space despite different internal designs.