6303-RSR-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6303-RSR-NTN model number is decoded

In the 6300-series (diameter series 3 of ISO 15) the last two digits encode the bore: 6303 carries bore code 17 = 17 mm. Outside diameter 47 mm and width 14 mm come from the ISO 15 boundary-dimensions general plan. Suffix -RSR denotes two low-friction non-contact elastomer seals; they keep coarse debris out with minimal drag but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 17 mm shaft, typical catalogue practice is a j5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NTN's non-contact seal suffix is LLB/LLF (catalogue number 6303LLB), mapped here from the industry-neutral -RSR spelling; speed capability matches the open bearing but it is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount this 17 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
• The 63xx medium series gains rating at 17 mm bore through a 47 mm OD and 14 mm width; the heavier rolling elements also trade away some speed versus a 6217.
• RSR low-friction seals on 6303-RSR-NTN run faster than contact-seal 6303-2RS but let fine dust and moisture past the non-contact lip; in dirty or wet duty specify 6303-2RS instead.
• The low-drag lip of 6303-RSR-NTN barely touches the inner ring; after long shelf storage the grease can separate, so rotate the rings by hand and confirm smooth, silent running before fitting.
• Shaft and housing fillets must clear the bearing chamfer so the 14 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• NTN catalogues this low-friction non-contact seal as 6303LLB (suffix LLB), mapped here from the industry-neutral -RSR spelling. NTN rates its speed capability the same as the open bearing, but it is not liquid-tight — for wet or fine-dust duty step up to the LLU contact seal (industry-neutral -2RS).
• At 17 mm bore the 6303 sits in NTN's small-bore range; ABEC-1/P0 runout is standard, and the pressed-steel cage is adequate up to the grease limiting speed — for higher accuracy (spindles, instruments) ask NTN for a P6 or P5 tolerance-class listing before relying on catalogue P0 figures.
• NTN rates 6303 at 14000 r/min grease limiting speed — this is an electric-motor range; keep the grease fill at 25–35% of the free bearing volume and avoid mixing grease thickener types if regreasing through the seal lip.
• At 15 kN dynamic load rating (C) and 6.55 kN static (C0), 0.51 kN fatigue load limit Cu, 6303 is a medium-load bearing suitable for most electric-motor and pump duty; the C0/C0r ratio matters for preloaded or thrust-loaded arrangements, so confirm the static safety factor with the NTN catalogue.
• At 115 g, 6303 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 17×47×14 mm envelope of 6303 gives a D/d ratio of 2.76 and 15.0 mm radial section height — a heavy section built for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 15/6.55 kN load ratings, 0.51 kN fatigue load limit Cu NTN lists the grease limiting speed at 14000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 115 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6303LLB on the 17×47×14 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6303 in a rated drive.
• Order the C3 internal-clearance version (6303 with C3 after the seal code) when the shaft fit is tight or the shaft-to-housing temperature gradient exceeds roughly 10 °C — the residual clearance after mounting, not the catalogue CN figure, decides service life.
• NTN's pressed-steel cage (no cage suffix) is the quiet standard for this size; for sustained running close to the limiting speed or for heavy shock duty, ask the NTN channel whether a machined-cage execution of 6303 is listed.