6306-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6306-NSK model number is decoded

In the 6300-series (diameter series 3 of ISO 15) the last two digits encode the bore: 6306 carries bore code 06 = 30 mm. Outside diameter 72 mm and width 19 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 30 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. In the NSK catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• A 30 mm shaft for 6306 should be finished to Ra ≤ 1.6 µm with square seating faces; at this bore a scored or oval journal shows up directly as running noise and early raceway damage.
• The 63xx medium section at 30 mm bore gains dynamic rating through larger rolling elements on a 72 mm OD; the penalty is mass and a lower limiting speed than the 6206 — do not specify it for speed-critical shafts.
• Storage matters for open bearings: 6306-NSK leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Open bearings tolerate the highest speeds in the 6300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 6306 units.
• Never mix components between two 6306-NSK units: rings, cage and balls are factory-matched and are not field-interchangeable, even between identical designations.
• A 30 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft.
• The open 6306 has no integral sealing; in the NSK E1103 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals). NSK does not offer a low-torque contact seal equivalent to NTN's LLH in this catalogue — for high-speed sealed duty specify the VV non-contact seal and an external housing labyrinth.
• The 30 mm bore puts 6306 in NSK's light industrial range; the standard pressed-steel cage and CN clearance cover most fractional-horsepower motor and small-pump duty. NSK's VV non-contact seal is the high-speed choice here — DDU contact seal costs roughly 30–40% of the open-bearing speed ceiling.
• At 29.3 kN dynamic load rating (C) and 15 kN static (C0), 6306 is a medium-load NSK bearing suitable for most electric-motor and pump duty; the C0/C0r ratio matters for preloaded or thrust-loaded arrangements, so confirm the static safety factor with the NSK catalogue.
• At 345 g, 6306 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 30×72×19 mm envelope of 6306 gives a D/d ratio of 2.40 and 21.0 mm radial section height — a heavy NSK section built for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 29.3/15 kN load ratings, mass 345 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6306 on the 30×72×19 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6306 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• When replacing a failed unit, inspect the shaft and housing seats before fitting the new 6306 — a new bearing pressed onto a worn or oval seat reproduces the original failure mode in a fraction of its expected life.
• Keep NSK bearings in the original packaging until fitting: the wrapper carries the production lot, and the unopened shelf life of greased sealed units is typically quoted at three to five years in dry, vibration-free storage.