6306-ZZ bearing: complete specifications & equivalents
The 6306-ZZ is a ISO 15 radial bearing sized 30 x 72 x 19 mm (bore x OD x width) with ZZ sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 30 mm |
| Outer diameter D | 72 mm |
| Width B | 19 mm |
| Material | GCr15 |
| Seal / shield | ZZ |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 29.6 kN |
| Basic static load rating C0 | 16 kN |
| Fatigue load limit Pu | 0.67 kN |
| Reference speed (thermal) | 20000 rpm |
| Limiting speed (mechanical) | 11000 rpm |
| Operating temperature | -30 to +120 °C |
| Mass | 360 g |
| Manufacturer designation | SKF 6306-2Z |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-25 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 6300-series range
| Bore d | 1.181 in |
|---|---|
| Outer diameter D | 2.835 in |
| Width B | 0.748 in |
| ISO bore code | 06 |
| Radial section height (D−d)/2 | 21 mm |
| Smallest bore in 6300-series | 2 mm |
| Largest outer diameter in 6300-series | 500 mm |
| Width range across 6300-series | 3–95 mm |
| Bore position in 6300-series (smallest first) | 13 of 40 |
| Bore above smallest 6300-series size | 28 mm |
Mounting, lubrication & life for 6306-ZZ
Recommended fits & mounting
- Rotating inner ring on a 30 mm shaft: k5; housing bore H7 for normal stationary-load outer rings. Reverse the logic if the outer ring rotates.
- Fit by induction heating (max 120 °C) where practical — never drive the ring home through the rolling elements.
- Keep shaft and housing fillet radii below the bearing chamfer so the 19 mm-wide ring seats square on its shoulder.
Lubrication strategy
Non-contact metal shields block coarse debris while running nearly as cool as open. No relubrication path on the standard execution; the shield cavity grease ages even though the steel is still serviceable.
Worked L10 life example (illustrative duty)
For ball bearings, L10h = (C/P)3 · 106 / (60·n). Taking an example radial equivalent load P = 3 kN at n = 1,500 r/min (a small belted motor duty — substitute the real equivalent load from the application calculation):
C = 29.6 kN → L10h ≈ 10,673 hours
Choosing a section at the same 30 mm bore
| Series | Open execution | OD × width | C (kN) | Limiting speed (r/min) |
|---|---|---|---|---|
| 60xx | 6006-FAG | 55 × 13 | 14.5 | 20,100 |
| 62xx | 6206-FAG | 62 × 16 | 22.0 | 17,800 |
| 63xx | 6306-FAG | 72 × 19 | 32.0 | 15,100 |
| 64xx | 6406-FAG | 90 × 23 | 42.5 | 11,000 |
| 618xx | 61806-FAG | 42 × 7 | 4.5 | 24,500 |
| 619xx | 61906-FAG | 47 × 9 | 7.2 | 21,700 |
| 160xx | 16006 | 55 × 9 | 11.2 | 18,500 |
A larger section is not a drop-in swap — OD and width change — and same-envelope seal variants are compared on the 30×72×19 envelope page. Match meaning, not the size chart alone: see what the cross-reference levels mean.
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 6306-2RS-FAG | FAG | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 30×72×19 mm envelope per ISO 15; seal variant differs (ZZ vs 2RS) — confirm sealing suits the duty. |
| 6306-FAG | FAG | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 30×72×19 mm envelope per ISO 15; seal variant differs (ZZ vs OPEN) — confirm sealing suits the duty. |
| 6306-ZZ-FAG | FAG | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 6306 | ISO 15 | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting. |
| 6306-2RS-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 30×72×19 mm envelope per ISO 15; seal variant differs (ZZ vs 2RS) — confirm sealing suits the duty. |
| 6306-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 30×72×19 mm envelope per ISO 15; seal variant differs (ZZ vs OPEN) — confirm sealing suits the duty. |
| 6306-RSR-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 30×72×19 mm envelope per ISO 15; seal variant differs (ZZ vs RSR) — confirm sealing suits the duty. |
| 6306-ZZ-NSK | NSK | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 6306-2RS-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 30×72×19 mm envelope per ISO 15; seal variant differs (ZZ vs 2RS) — confirm sealing suits the duty. |
| 6306-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 30×72×19 mm envelope per ISO 15; seal variant differs (ZZ vs OPEN) — confirm sealing suits the duty. |
| 6306-RSR-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 30×72×19 mm envelope per ISO 15; seal variant differs (ZZ vs RSR) — confirm sealing suits the duty. |
| 6306-ZZ-NTN | NTN | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 7306 | SKF | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | — |
| NU306 | SKF | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | — |
| W6306-2RS | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF stainless execution W 6306-2RS1 shares the 30×72×19 mm envelope but rates differently (29.6/16 kN vs 22.9/15 kN) — not a load-rating equivalent. |
| W6306-ZZ | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF stainless execution W 6306-2Z shares the 30×72×19 mm envelope but rates differently (29.6/16 kN vs 22.9/15 kN) — not a load-rating equivalent. |
| W6306 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF stainless execution W 6306 shares the 30×72×19 mm envelope but rates differently (29.6/16 kN vs 22.9/15 kN) — not a load-rating equivalent. |
| 306 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF 306 shares the 30×72×19 mm envelope but catalogue C/C0 differ — envelope match only after a load check. |
| 306-ZZ | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF 306-2Z shares the 30×72×19 mm envelope but catalogue C/C0 differ — envelope match only after a load check. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 6306-ZZ model number is decoded
In the 6300-series (diameter series 3 of ISO 15) the last two digits encode the bore: 6306 carries bore code 06 = 30 mm. Outside diameter 72 mm and width 19 mm come from the ISO 15 boundary-dimensions general plan. Suffix -ZZ denotes two non-contact metallic shields; they retain grease and block coarse debris but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 30 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. SKF's own suffix is 2Z (this page's industry-neutral spelling is -ZZ); catalogue number 6306-2Z.
Typical equipment & failure modes
Common applications
- agricultural equipment
- fans and blowers
- electric motors
- centrifugal pumps
Known failure patterns
- fine-particle abrasion when non-contact shields let dust past in dirty duty
- grease aging in the shield-for-life cavity with no relubrication path
- cage damage from operation beyond the limiting speed
- electrical pitting in VFD-driven motors without grounding protection
Selection pitfalls — read before you substitute
- Sizes around 30 mm bore are normally pressed on cold with a sleeve against the inner-ring face; the press force must never route through the outer ring or the balls of 6306-ZZ.
- The 63xx medium section at 30 mm bore gains dynamic rating through larger rolling elements on a 72 mm OD; the penalty is mass and a lower limiting speed than the 6206 — do not specify it for speed-critical shafts.
- ZZ shields are non-contact: 6306-ZZ blocks chips and coarse dust but is not waterproof — do not install it expecting a pressure-wash seal, step up to 6306-2RS for that.
- Shielded 6306-ZZ units are typically greased for life; prying the shields out for regreasing usually bends them and leaves a gap that throws grease in service.
- Vibration during standstill brinells the raceways of a 30 mm bearing at ball spacing; if the machine sits idle next to running equipment, turn the shaft over periodically or isolate the arrangement.
- Suffixes stack in a defined order — clearance follows the seal code, e.g. 6306-C3. No clearance suffix means normal CN clearance.
- SKF spells the shielded version 6306-2Z (one shield: 6306-Z), not "-ZZ": the suffix language differs by brand even though the ISO envelope is identical, so quote the brand designation when ordering.
- The single-shield execution 6306-Z is a distinct order number in catalogue 17000: it suits open gears or oil-bath arrangements where the unshielded face faces the lubricant, and it is not interchangeable with the double-shield 6306-2Z for high-contamination positions.
- The 29.6/16 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 6306-ZZ bearing?
A 6306-ZZ deep-groove ball bearing has a 30 mm bore, 72 mm outer diameter and 19 mm width (1.181 × 2.835 × 0.748 in), per ISO 15 boundary dimensions. It is fitted with two non-contact metallic shields.
What lubrication does 6306-ZZ need?
6306-ZZ is greased at the factory and the shields hold the fill for the bearing's service life; relubrication is not intended, and adding grease through the shield gap usually forces dirt in with it.
How does the 6306 bore code work?
The last two digits of 6306 are bore code 06, giving 06 × 5 = 30 mm bore. The 72 mm outside diameter and 19 mm width follow the ISO 15 diameter series, not the bore code alone.
What does the ZZ suffix on 6306-ZZ mean?
ZZ means two non-contact sheet-metal shields, one each side. They retain factory grease and block coarse particles with little friction, but do not seal against liquids, fine dust or pressure washing.
What is the SKF designation and catalogue data for 6306-ZZ?
In the SKF Rolling Bearings catalogue this size is listed as 6306-2Z — two non-contact sheet-metal shields, 30×72×19 mm per ISO 15. Quoted values: C 29.6 kN, C0 16 kN, Pu 0.67 kN, limiting speed 11000 r/min, mass 360 g. Brand suffixes (2Z, 2RSH, 2RSL) differ from the industry-neutral spelling 6306-ZZ.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-25. Read our editorial & correction policy.