6316-RSR-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6316-RSR-NTN model number is decoded

In the 6300-series (diameter series 3 of ISO 15) the last two digits encode the bore: 6316 carries bore code 16 = 80 mm. Outside diameter 170 mm and width 39 mm come from the ISO 15 boundary-dimensions general plan. Suffix -RSR denotes two low-friction non-contact elastomer seals; they keep coarse debris out with minimal drag but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 80 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NTN's non-contact seal suffix is LLB/LLF (catalogue number 6316LLB), mapped here from the industry-neutral -RSR spelling; speed capability matches the open bearing but it is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Large bores like the 80 mm of 6316-RSR-NTN demand clean, burr-free seats; one raised burr under a ring this size cocks the bearing and concentrates load at the raceway edge, cutting life drastically.
• The 63xx medium section at 80 mm bore gains dynamic rating through larger rolling elements on a 170 mm OD; the penalty is mass and a lower limiting speed than the 6216 — do not specify it for speed-critical shafts.
• RSR low-friction seals on 6316-RSR-NTN run faster than contact-seal 6316-2RS but let fine dust and moisture past the non-contact lip; in dirty or wet duty specify 6316-2RS instead.
• The low-drag lip of 6316-RSR-NTN barely touches the inner ring; after long shelf storage the grease can separate, so rotate the rings by hand and confirm smooth, silent running before fitting.
• Measure the shaft, do not trust the drawing: a 80 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 6316-RSR-NTN.
• Never mix components between two 6316-RSR-NTN units: rings, cage and balls are factory-matched and are not field-interchangeable, even between identical designations.
• NTN catalogues this low-friction non-contact seal as 6316LLB (suffix LLB), mapped here from the industry-neutral -RSR spelling. NTN rates its speed capability the same as the open bearing, but it is not liquid-tight — for wet or fine-dust duty step up to the LLU contact seal (industry-neutral -2RS).
• At 80 mm bore 6316 is in NTN's upper general-purpose range; the pressed-steel cage is standard but mid-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NTN channel if the application sees impact loads.
• NTN lists the grease limiting speed at 4000 r/min for 6316; this is a large or heavy-section size where centrifugal force and cage inertia cap the speed — for higher shaft speeds either step to a smaller bearing on the same bore or consult NTN for an oil-lubricated, machined-cage variant.
• At 136 kN dynamic load rating (C) and 86.5 kN static (C0), 6.05 kN fatigue load limit Cu, 6316 is a heavy-load bearing for industrial gearboxes and large conveyors; NTN expects a machined brass cage (suffix M) at this rating for shock duty, and the static C0 must be checked against any mounting or lifting loads.
• At 3590 g (3.6 kg), 6316 needs mechanical handling for mounting; NTN recommends induction heating the inner ring (max 120 °C) rather than pressing cold, and a lifting eye if the housing is pre-assembled.
• The 80×170×39 mm envelope of 6316 gives a D/d ratio of 2.13 and 45.0 mm radial section height — a heavy section built for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 136/86.5 kN load ratings, 6.05 kN fatigue load limit Cu NTN lists the grease limiting speed at 4000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 3590 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6316LLB on the 80×170×39 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6316 in a rated drive.
• Factory-fill grease in NTN sealed units is a general-duty lithium-soap grease; food-grade, low-temperature and high-temperature fills are request options at order time, because LLU/LLB units are not meant to be opened and re-greased in the field.
• Order the C3 internal-clearance version (6316 with C3 after the seal code) when the shaft fit is tight or the shaft-to-housing temperature gradient exceeds roughly 10 °C — the residual clearance after mounting, not the catalogue CN figure, decides service life.