63007-2RS bearing: complete specifications & equivalents

The 63007-2RS is a ISO 15 radial bearing sized 35 x 62 x 20 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 62 mm d = 35 B = 20 mm side section front view
Principal dimensions: bore d 35 mm, outer diameter D 62 mm, width B 20 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 35 mm
Outer diameter D 62 mm
Width B 20 mm
Material GCr15
Seal / shield 2RS
Internal clearance CN
Tolerance class P0
Cage steel, stamped ribbon (J-type)
Basic dynamic load rating C 15.9 kN
Basic static load rating C0 10.2 kN
Fatigue load limit Pu 0.44 kN
Limiting speed (mechanical) 7000 rpm
Operating temperature -40 to +120 °C
Mass 220 g
Manufacturer designation 63007-2RS1
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 63000-series range

Bore d1.378 in
Outer diameter D2.441 in
Width B0.787 in
ISO bore code07
Radial section height (D−d)/213.5 mm
Smallest bore in 63000-series10 mm
Largest outer diameter in 63000-series80 mm
Width range across 63000-series12–23 mm
Bore position in 63000-series (smallest first)8 of 11
Bore above smallest 63000-series size25 mm

Cross references & equivalents

No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.

How the 63007-2RS model number is decoded

The 63000-series is the wide-section counterpart of the standard deep-groove family (extra width code built into the designation); the last two digits encode the bore: 63007 carries code 07 = 35 mm (code × 5). The envelope is 35×62×20 mm (1.378×2.441×0.787 in) with a 13.5 mm radial section height, C 15.9 kN, C0 10.2 kN and Pu 0.44 kN. SKF catalogues the sealed execution as 63007-2RS1: two contact elastomer lips (2RS1/2RSH spelling) over a lifetime grease fill; the lips add drag, and no reference (thermal) speed is published. Limiting speed 7000 r/min, catalogue mass 220 g.

Typical equipment & failure modes

Common applications

  • centrifugal and positive-displacement pumps
  • material-handling equipment
  • industrial fans
  • compressor drives

Known failure patterns

  • contact-seal lip hardening and pre-grease loss after long high-temperature service
  • grease-life expiry inside the sealed-for-life cavity, which has no relubrication path
  • rolling-contact fatigue spalling once the catalogue L10 life is exceeded
  • brinelling from static overload or hammer blows during mounting

Selection pitfalls — read before you substitute

  • The fatigue load limit is 0.44 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
  • Clearance suffixes follow the seal code in the designation stack (e.g. 63007-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
  • Contact seals make 63007-2RS slower than the open 63007 (limiting 7000 r/min) and forbid solvent washing, which destroys the lifetime grease.
  • Do not pry the caps off 63007-2RS to repack it; shield/seal damage leaves a gap that throws grease and admits dirt.
  • Deep-groove geometry tolerates only minutes of misalignment; if the 62 mm housing bore cannot be aligned, move to a self-aligning bearing rather than shimming 63007-2RS.
  • Do not preload 63007-2RS to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
  • SKF Explorer deep-groove bearings of this size are produced to tight internal-geometry control; rating revisions between catalogue years do not change the designation, so keep the catalogue edition with the machine documentation.
  • SKF date-codes its packaging, and greased sealed or shielded bearings carry a finite shelf life: rotate stock first-in-first-out and store boxes dry, cool and away from vibration.

Frequently asked questions

What are the dimensions of 63007-2RS?

The SKF 63007-2RS1 measures 35 mm bore × 62 mm OD × 20 mm width (1.378 × 2.441 × 0.787 in), mass about 220 g. It has two contact rubber seals and a lifetime grease fill.

How does the bore code in 63007 work?

The final two digits of 63007 are bore code 07, multiplied by 5 to give 35 mm.

How long can a greased 63007-2RS be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

What load can 63007-2RS take?

Catalogue values for 63007-2RS1: dynamic C 15.9 kN, static C0 10.2 kN, fatigue limit Pu 0.44 kN. Use C in life calculation and C0 for static checks at 35 mm bore.

What is the speed rating of 63007-2RS?

SKF publishes only the 7000 r/min limiting speed for this execution; sealed variants have no thermal reference speed because seal and grease life govern.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.