2200-ETN9 bearing: complete specifications & equivalents
The 2200-ETN9 is a ISO 15 radial bearing sized 10 x 30 x 14 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 10 mm |
| Outer diameter D | 30 mm |
| Width B | 14 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | polymer (PA66 glass-fibre reinforced) |
| Basic dynamic load rating C | 8.06 kN |
| Basic static load rating C0 | 1.73 kN |
| Fatigue load limit Pu | 0.09 kN |
| Reference speed (thermal) | 50000 rpm |
| Limiting speed (mechanical) | 34000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 47 g |
| Manufacturer designation | 2200 ETN9 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 2200-series range
| Bore d | 0.394 in |
|---|---|
| Outer diameter D | 1.181 in |
| Width B | 0.551 in |
| ISO bore code | 00 |
| Radial section height (D−d)/2 | 10 mm |
| Smallest bore in 2200-series | 10 mm |
| Largest outer diameter in 2200-series | 200 mm |
| Width range across 2200-series | 14–53 mm |
| Bore position in 2200-series (smallest first) | 1 of 23 |
| Bore above smallest 2200-series size | 0 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 2200 | NTN | full Dimensions and internal design equivalent — standard interchange. | NTN counterpart 2200S on the same 10×30×14 mm envelope with ratings within 10 % — interchange after checking seal, cage and bore details on both pages. |
| 2200-E-2RS1TN9 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 10×30×14 mm envelope, but catalogue C/C0 differ between executions (8.06/1.73 kN vs 5.53/1.18 kN) — boundary dimensions match, not a load-rating equivalent. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 2200-ETN9 model number is decoded
The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). bore code 00 follows the 10/12/15/17 mm exception table, so 2200 fits a 10 mm shaft. Envelope 10×30×14 mm (0.394×1.181×0.551 in) with a 10.0 mm radial section height, C 8.06 kN, C0 1.73 kN and Pu 0.09 kN. The open 2200 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 10 mm shaft. Reference (thermal) speed 50000 r/min, limiting speed 34000 r/min, catalogue mass 47 g.
Typical equipment & failure modes
Common applications
- woodworking machine spindles
- light gearbox layshafts
- food-processing conveyors
- small electric motors
Known failure patterns
- contamination wear when the open arrangement is used without adequate external sealing
- lubricant starvation where no regreasing interval is maintained
- brinelling from static overload or hammer blows during mounting
- false brinelling from vibration while the shaft stands idle
Selection pitfalls — read before you substitute
- The spherical outer raceway lets 2200-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.
- Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2200-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.
- The ETN9 suffix on 2200-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 34000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.
- Fillet radii must clear the 2200-ETN9 chamfer so the 14 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
- Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2200-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.
- Assign interference to the rotating ring: on a 10 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates.
Frequently asked questions
What are the dimensions of 2200-ETN9?
SKF 2200 ETN9 measures 10 mm bore × 30 mm OD × 14 mm width (0.394 × 1.181 × 0.551 in), mass about 47 g. It is open, with no shields or seals.
How does the bore code in 2200 work?
Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 2200 fits a 10 mm shaft. Code × 5 starts at code 04.
What is the speed rating of 2200-ETN9?
SKF lists a 50000 r/min thermal reference speed and a 34000 r/min mechanical limiting speed for 2200 ETN9; real limits also depend on lubrication and fits.
How much misalignment can 2200-ETN9 tolerate?
Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2200-ETN9 allow less (about 1°) because the seal lip binds first.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.