2213-ETN9 bearing: complete specifications & equivalents
The 2213-ETN9 is a ISO 15 radial bearing sized 65 x 120 x 31 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 65 mm |
| Outer diameter D | 120 mm |
| Width B | 31 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | polymer (PA66 glass-fibre reinforced) |
| Basic dynamic load rating C | 57.2 kN |
| Basic static load rating C0 | 20 kN |
| Fatigue load limit Pu | 1.02 kN |
| Reference speed (thermal) | 10000 rpm |
| Limiting speed (mechanical) | 7000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 1450 g |
| Manufacturer designation | 2213 ETN9 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 2200-series range
| Bore d | 2.559 in |
|---|---|
| Outer diameter D | 4.724 in |
| Width B | 1.22 in |
| ISO bore code | 13 |
| Radial section height (D−d)/2 | 27.5 mm |
| Smallest bore in 2200-series | 10 mm |
| Largest outer diameter in 2200-series | 200 mm |
| Width range across 2200-series | 14–53 mm |
| Bore position in 2200-series (smallest first) | 14 of 23 |
| Bore above smallest 2200-series size | 55 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 2213 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 65×120×31 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
| 2213-E-2RS1TN9 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 65×120×31 mm envelope, but catalogue C/C0 differ between executions (57.2/20 kN vs 35.1/14 kN) — boundary dimensions match, not a load-rating equivalent. |
| 2213-E-2RS1KTN9 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 65×120×31 mm envelope, but catalogue C/C0 differ between executions (57.2/20 kN vs 35.1/14 kN) — boundary dimensions match, not a load-rating equivalent. |
| 2213-EKTN9 | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 65×120×31 mm envelope with catalogue ratings within 10 %; 2213 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 2213-ETN9 model number is decoded
The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2213 carries code 13 = 65 mm (code × 5). Envelope 65×120×31 mm (2.559×4.724×1.22 in) with a 27.5 mm radial section height, C 57.2 kN, C0 20 kN and Pu 1.02 kN. The open 2213 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 65 mm shaft. Reference (thermal) speed 10000 r/min, limiting speed 7000 r/min, catalogue mass 1450 g.
Typical equipment & failure modes
Common applications
- conveyor drum and pulley shafts
- agricultural gearboxes
- textile machinery drives
- industrial fans and blowers
Known failure patterns
- contamination wear when the open arrangement is used without adequate external sealing
- lubricant starvation where no regreasing interval is maintained
- raceway smearing under marginal lubrication at start-up
- electrical pitting in VFD-driven motors without shaft grounding
Selection pitfalls — read before you substitute
- Catalogue ratings for 2213-ETN9 (C 57.2 kN, C0 20 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
- The fatigue load limit is 1.02 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
- The ETN9 suffix on 2213-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 7000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.
- Fillet radii must clear the 2213-ETN9 chamfer so the 31 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
- Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2213-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.
- Assign interference to the rotating ring: on a 65 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.
Frequently asked questions
What are the dimensions of 2213-ETN9?
SKF 2213 ETN9 measures 65 mm bore × 120 mm OD × 31 mm width (2.559 × 4.724 × 1.22 in), mass about 1450 g. It is open, with no shields or seals.
How does the bore code in 2213 work?
The final two digits of 2213 are bore code 13, multiplied by 5 to give 65 mm.
Can 2213-ETN9 take axial load?
A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement.
Which fits should I use for 2213-ETN9?
With a rotating inner ring use roughly k5 on the shaft and H7 in the 120 mm housing; reverse the interference if the outer ring rotates.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.