2213 bearing: complete specifications & equivalents
The 2213 is a ISO 15 radial bearing sized 65 x 120 x 31 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 65 mm |
| Outer diameter D | 120 mm |
| Width B | 31 mm |
| Seal / shield | open |
| Basic dynamic load rating C | 43.5 kN |
| Basic static load rating C0 | 16.4 kN |
| Fatigue load limit Pu | 0.92 kN |
| Limiting speed (mechanical) | 4800 rpm |
| Mass | 1500 g |
| Manufacturer designation | 2213S |
| Standard | ISO 15 |
| Catalog version | CAT. No. 2203-3/E 2024 |
| Last verified | 2026-09-25 |
Source: catalog reference (CAT. No. 2203-3/E 2024) · extracted 2026-09-25
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (CAT. No. 2203-3/E 2024); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 2200-series range
| Bore d | 2.559 in |
|---|---|
| Outer diameter D | 4.724 in |
| Width B | 1.22 in |
| ISO bore code | 13 |
| Radial section height (D−d)/2 | 27.5 mm |
| Smallest bore in 2200-series | 10 mm |
| Largest outer diameter in 2200-series | 200 mm |
| Width range across 2200-series | 14–53 mm |
| Bore position in 2200-series (smallest first) | 14 of 23 |
| Bore above smallest 2200-series size | 55 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the 2213 model number is decoded
In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2213 carries bore code 13 = 65 mm. Outside diameter 120 mm and width 31 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.
Typical equipment & failure modes
Common applications
- paper mill and processing equipment shafts
- industrial electric motor shafts
- pump and compressor drive shafts
- gearbox and speed reducer shafts
Known failure patterns
- contamination wear from dust and dirt ingress through the open arrangement
- lubricant starvation when no regreasing interval is maintained
- edge loading and stress concentration from excessive misalignment beyond the allowable angle
- raceway smearing under marginal lubrication at start-up
Selection pitfalls — read before you substitute
- Temperature rise and interference fits consume internal clearance on this 65 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2213 with C3 for those conditions.
- The 22xx wide-section at 65 mm bore adds load capacity through increased 31 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1213.
- The open 2213 has no lubricant retention: grease escapes and contaminants migrate straight into the 65×120×31 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
- Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2213 units.
- Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing.
Frequently asked questions
What are the dimensions of a 2213 self-aligning ball bearing?
A 2213 self-aligning ball bearing has a 65 mm bore, 120 mm outer diameter and 31 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting.
How does the 2213 bore code work?
The last two digits of 2213 are bore code 13, giving 13 × 5 = 65 mm bore. The 120 mm outside diameter and 31 mm width follow the ISO 15 diameter series, not the bore code alone.
What does the open suffix mean on 2213?
A bare 2213 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication.
How does the 2200 compare with other self-aligning series at the same 65 mm bore?
The 22xx is the wide light section: 120×31 mm with a 27.5 mm radial section at 65 mm bore, wider than a 1213 for higher load capacity at the cost of speed.
Reviewed & verified by the MPN Base engineering desk against source catalog CAT. No. 2203-3/E 2024 on 2026-09-25. Read our editorial & correction policy.