2307-EKTN9 bearing: complete specifications & equivalents
The 2307-EKTN9 is a ISO 15 radial bearing sized 35 x 80 x 31 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 35 mm |
| Outer diameter D | 80 mm |
| Width B | 31 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | polymer (PA66 glass-fibre reinforced) |
| Basic dynamic load rating C | 39.7 kN |
| Basic static load rating C0 | 11.2 kN |
| Fatigue load limit Pu | 0.59 kN |
| Reference speed (thermal) | 16000 rpm |
| Limiting speed (mechanical) | 12000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 680 g |
| Manufacturer designation | 2307 EKTN9 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 2300-series range
| Bore d | 1.378 in |
|---|---|
| Outer diameter D | 3.15 in |
| Width B | 1.22 in |
| ISO bore code | 07 |
| Radial section height (D−d)/2 | 22.5 mm |
| Smallest bore in 2300-series | 10 mm |
| Largest outer diameter in 2300-series | 215 mm |
| Width range across 2300-series | 17–73 mm |
| Bore position in 2300-series (smallest first) | 8 of 21 |
| Bore above smallest 2300-series size | 25 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 2307 | NTN | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 2307-E-2RS1TN9 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 35×80×31 mm envelope, but catalogue C/C0 differ between executions (39.7/11.2 kN vs 26.5/8.5 kN) — boundary dimensions match, not a load-rating equivalent. |
| 2307-E-2RS1KTN9 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 35×80×31 mm envelope, but catalogue C/C0 differ between executions (39.7/11.2 kN vs 26.5/8.5 kN) — boundary dimensions match, not a load-rating equivalent. |
| 2307-ETN9 | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 35×80×31 mm envelope with catalogue ratings within 10 %; 2307 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 2307-EKTN9 model number is decoded
The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2307 carries code 07 = 35 mm (code × 5). Envelope 35×80×31 mm (1.378×3.15×1.22 in) with a 22.5 mm radial section height, C 39.7 kN, C0 11.2 kN and Pu 0.59 kN. The open 2307 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 16000 r/min, limiting speed 12000 r/min, catalogue mass 680 g.
Typical equipment & failure modes
Common applications
- industrial fans and blowers
- woodworking machinery
- pump shafts with mild misalignment
- material-handling equipment
Known failure patterns
- lubricant starvation where no regreasing interval is maintained
- contamination wear when the open arrangement is used without adequate external sealing
- incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance
- adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder
- rolling-contact fatigue spalling once the catalogue L10 life is exceeded
- brinelling from static overload or hammer blows during mounting
Selection pitfalls — read before you substitute
- At 35 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.
- Fillet radii must clear the 2307-EKTN9 chamfer so the 31 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
- The K suffix means a 1:12 tapered bore: 2307-EKTN9 is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.
- The EKTN9 suffix on 2307-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 12000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.
- Mount 2307-EKTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.
- The fatigue load limit is 0.59 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
Frequently asked questions
What are the dimensions of 2307-EKTN9?
SKF 2307 EKTN9 measures 35 mm bore × 80 mm OD × 31 mm width (1.378 × 3.15 × 1.22 in), mass about 680 g. It is open, with no shields or seals.
How does the bore code in 2307 work?
The final two digits of 2307 are bore code 07, multiplied by 5 to give 35 mm.
How much misalignment can 2307-EKTN9 tolerate?
Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2307-EKTN9 allow less (about 1°) because the seal lip binds first.
Can 2307-EKTN9 take axial load?
A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.