YAR-207-106-2F bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-28

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the YAR-207-106-2F model number is decoded

YAR 207-106-2F is SKF's 34.925 mm-bore grub-screw insert bearing with the inner ring extended on both sides in the YAR2 series — a Y-bearing with a spherically ground outside surface for static self-alignment inside a matching SKF Y-housing, boundary dimensions 34.925x72x42.9 mm. Wide-inner-ring deep-groove ball geometry carries the load: the extended inner ring gives the shaft grip and the seal lands, while the outer ring stays narrow and spherically ground on its outside surface. the YAR prefix names SKF grub-screw Y-bearings: two set screws in the extended inner ring lock the shaft at a 120 deg angle, and the inner ring extends symmetrically on both sides. the three-digit -106 tail codes the bore in inches for inch-shaft bearings: 1 whole inch 6/16 in = 34.925 mm (first digit whole inches, next two sixteenths of an inch). suffix -2F means an NBR rubber contact seal plus a plain pressed-steel flinger on EACH side: the lip rides the extended inner ring while the flinger sheds coarse contamination before it reaches the lip. Envelope 34.925x72x42.9 mm (1.375x2.835x1.689 in), outer ring 19 mm wide, C 25.5 kN, C0 15.3 kN, Pu 0.655 kN. The catalogue publishes a single speed ceiling, the limiting speed: 5,300 r/min; mass 450 g. Spherical-seat note in numbers: the 72 mm OD is ground spherical, so the self-aligning pivot happens on a circle roughly pi x 53.462 = 167.956 mm in mean circumference — keep that interface greased, because corrosion locking turns the pivot into a fixed misaligned mount. Speed ceiling of 5,300 r/min is the catalogue mechanical limit for THIS execution; seal lip and flinger drag, not steel fatigue, are normally what cap it, so real fan duty is planned well below it. Static-first planning: the 0.357 kN of C0 per overall-width millimetre is the figure for belt tension peaks and rotor imbalance standstill loads on the 34.925 mm shaft, not the 25.5 kN L10 value. Fillet discipline: the printed r_min 1 mm limit means shaft and housing fillets must stay under that radius; a fillet that bottoms the 34.925x72 mm insert on its chamfer tilts the whole spherical seat. Grease-life arithmetic is dominated by speed: at dn approx 2.83x10^5 the sealed-for-life fill is planned for the catalogue's grease-life regime, which is why the limiting speed and the relubrication interval move together, and high-temperature mounts shorten both even when load is light. Both-sides sealed order-number note: the two set screws clamp through dimpled recesses in the extended inner ring; tighten alternately to the catalogue procedure and retighten after the first run-in period, because the -2F flingers keep dust out but cannot compensate for a screw that walked loose. Service tip for YAR-207-106-2F: dimpled or drilled shaft spots under the screw points are sometimes specified on shock duty, but the standard mounting relies on point indentation alone — never substitute longer screws that reach the 18.538 mm radial section.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• The 25.4 mm s1 dimension is the screw seating geometry inside the 23.9 mm of extended inner ring; a shaft step that crowds that side prevents the screws reaching the shaft squarely.
• Replacement discipline: a YAR insert is not interchangeable with an eccentric-collar unit of the same envelope — the shaft may need spot-facing or collar space that does not exist.
• Do not specify the 34.925 mm grub-screw insert for a shaft harder than about 45 HRC without dimples: the screw points skate on hard surfaces and the unit creeps regardless of tightening torque.
• The 25.5/15.3 kN figures belong specifically to YAR 207-106-2F; HV stainless, AG agricultural and VE495 zinc-plated variants of the same envelope publish derated values, so write the complete order number including suffixes on the purchase and maintenance records.