YAR-207-106-2RF-HV bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-28

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the YAR-207-106-2RF-HV model number is decoded

The YAR2 series order number YAR 207-106-2RF/HV is a SKF insert bearing (Y-bearing) for a 34.925 mm (1.375 in) shaft: grub-screw insert bearing with the inner ring extended on both sides, built to the ISO 15 diameter-series envelope with a sphered OD of 72 mm. Inside is a sealed deep-groove ball set with an extended inner ring, two set screws 120 deg apart doing the shaft locking, and the sphered outer ring providing the unit's static alignment pivot. reading the YAR basic designation: set-screw shaft locking with the screws spaced 120 deg apart; YAR carries the symmetric, both-sides-extended inner ring. inch bore code -106 decodes as 1" +6/16, i.e. 34.925 mm; the metric coded size YAR 207 shares the same envelope but its bore is the metric value, not this one. the HV suffix means stainless rings and balls with food-grade compliant seals and grease; capacity is derated versus the carbon-steel part. Envelope 34.925x72x42.9 mm (1.375x2.835x1.689 in), outer ring 19 mm wide, C 21.6 kN, C0 15.3 kN, Pu 0.655 kN. The catalogue publishes a single speed ceiling, the limiting speed: 3,200 r/min; mass 450 g. Static-first planning: the 0.357 kN of C0 per overall-width millimetre is the figure for belt tension peaks and rotor imbalance standstill loads on the 34.925 mm shaft, not the 21.6 kN L10 value. Pitch-diameter arithmetic: dm = (34.925+72)/2 = 53.462 mm; at the 3,200 r/min limiting speed the ball set runs at dn approx 1.71x10^5, reduced from an open bearing mainly by seal lip friction and the life-long grease fill. Inner-geometry cross-reference: the catalogue shoulder diameters (d1 46.1 mm) set the shaft-abutment and sleeve limits; an abutment larger than these numbers contacts the seal or the inner flinger. Grease-life arithmetic is dominated by speed: at dn approx 1.71x10^5 the sealed-for-life fill is planned for the catalogue's grease-life regime, which is why the limiting speed and the relubrication interval move together, and high-temperature mounts shorten both even when load is light. Bore-to-OD planning: OD 72 over bore 34.925 is a 2.062x step, while bore/overall-width gives 0.814; the spherical seat in the matching Y-housing must be specified to the 72 mm OD, not to a cylindrical housing bore. Stainless food-range note: HV parts trade some capacity for corrosion resistance and food-compatible lubrication, and the printed limiting speed is set for that fill; do not top up with ordinary mineral grease in service — mixing greases can harden the food-grade fill and seize the seals. Set-screw geometry on this size: the two 120 deg screws bear on the 34.925 mm shaft inside the 42.9 mm total width while the outer ring is only 19 mm wide, leaving the extended ring to carry the screw points clear of the ball track.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• The 25.4 mm s1 dimension is the screw seating geometry inside the 23.9 mm of extended inner ring; a shaft step that crowds that side prevents the screws reaching the shaft squarely.
• Do not specify the 34.925 mm grub-screw insert for a shaft harder than about 45 HRC without dimples: the screw points skate on hard surfaces and the unit creeps regardless of tightening torque.
• Replacement discipline: a YAR insert is not interchangeable with an eccentric-collar unit of the same envelope — the shaft may need spot-facing or collar space that does not exist.
• The 21.6/15.3 kN figures belong specifically to YAR 207-106-2RF/HV; HV stainless, AG agricultural and VE495 zinc-plated variants of the same envelope publish derated values, so write the complete order number including suffixes on the purchase and maintenance records.