YAR-208-108-2F bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-28

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the YAR-208-108-2F model number is decoded

The YAR2 series order number YAR 208-108-2F is a SKF insert bearing (Y-bearing) for a 38.099999999999994 mm (1.5 in) shaft: grub-screw insert bearing with the inner ring extended on both sides, built to the ISO 15 diameter-series envelope with a sphered OD of 80 mm. Inside is a sealed deep-groove ball set with an extended inner ring, two set screws 120 deg apart doing the shaft locking, and the sphered outer ring providing the unit's static alignment pivot. reading the YAR basic designation: set-screw shaft locking with the screws spaced 120 deg apart; YAR carries the symmetric, both-sides-extended inner ring. inch bore code -108 decodes as 1" +8/16, i.e. 38.1 mm; the metric coded size YAR 208 shares the same envelope but its bore is the metric value, not this one. the -2F external design pairs a nitrile contact seal with a plain sheet-steel thrower on both sides — a two-stage exclusion chain of flinger first, sealing lip second, typical of farm and conveyor duty. Envelope 38.099999999999994x80x49.2 mm (1.5x3.15x1.937 in), outer ring 21 mm wide, C 30.7 kN, C0 19 kN, Pu 0.8 kN. The catalogue publishes a single speed ceiling, the limiting speed: 4,800 r/min; mass 650 g. Outer-vs-overall width: the outer ring is 21 mm wide inside the 49.2 mm total, so the extended inner ring accounts for 0.573 of the overall width (14.1 mm of axial projection per side). Imperial procurement cross-check: 1.5 in bore, 3.15 in OD, 1.937 in overall width; the 650 g mass converts to 0.650 kg (22.9 oz) for the bill of materials. Load balance for documentation: C0 19 kN against C 30.7 kN gives a 0.619 ratio; mounted-unit positions with shock and standstill loading are normally checked on C0, while conveyor and fan duty are evaluated on the L10 figure. Rating split for the maintenance file: dynamic 30.7 kN (L10), static 19 kN (s0 shock check), fatigue 0.8 kN (adjusted life) — three separate uses for YAR 208-108-2F, none interchangeable with another. Fillet discipline: the printed r_min 1 mm limit means shaft and housing fillets must stay under that radius; a fillet that bottoms the 38.099999999999994x80 mm insert on its chamfer tilts the whole spherical seat. Both-sides sealed order-number note: the two set screws clamp through dimpled recesses in the extended inner ring; tighten alternately to the catalogue procedure and retighten after the first run-in period, because the -2F flingers keep dust out but cannot compensate for a screw that walked loose. Service tip for YAR-208-108-2F: dimpled or drilled shaft spots under the screw points are sometimes specified on shock duty, but the standard mounting relies on point indentation alone — never substitute longer screws that reach the 20.95 mm radial section.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Replacement discipline: a YAR insert is not interchangeable with an eccentric-collar unit of the same envelope — the shaft may need spot-facing or collar space that does not exist.
• Do not specify the 38.099999999999994 mm grub-screw insert for a shaft harder than about 45 HRC without dimples: the screw points skate on hard surfaces and the unit creeps regardless of tightening torque.
• The 30.2 mm s1 dimension is the screw seating geometry inside the 28.2 mm of extended inner ring; a shaft step that crowds that side prevents the screws reaching the shaft squarely.
• Ordering discipline for the 38.099999999999994 mm size: the chapter lists several executions side by side (YAR2 locking style x seal package x application variant); a bare-number substitution needs a fresh dimension, speed and rating check rather than a like-for-like assumption.