N206EA bearing: complete specifications & equivalents
The N206EA is a ISO 15 radial bearing sized 30 x 62 x 16 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 30 mm |
| Outer diameter D | 62 mm |
| Width B | 16 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 46 kN |
| Basic static load rating C0 | 37.5 kN |
| Fatigue load limit Pu | 4.55 kN |
| Limiting speed (mechanical) | 11000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 205 g |
| Manufacturer designation | NTN N206EA |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & N200-series range
| Bore d | 1.181 in |
|---|---|
| Outer diameter D | 2.441 in |
| Width B | 0.63 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 16 mm |
| Smallest bore in N200-series | 17 mm |
| Largest outer diameter in N200-series | 580 mm |
| Width range across N200-series | 12–92 mm |
| Bore position in N200-series (smallest first) | 4 of 35 |
| Bore above smallest N200-series size | 13 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| N206EA | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the N206EA model number is decoded
N206EA is the standard section of the NTN N200 dimension series for a 30 mm shaft — 46 kN of basic dynamic capacity in a 205 g, open bearing. Numbering ties N206EA to its envelope: type code N, series N200, 30 mm bore; the 62×16 mm outline therefore swaps dimensionally with other ISO 15 bearings of the same code, though rib arrangements differ by prefix. NTN ships these bearings open with normal (CN) radial clearance and P0 tolerance as standard; precision classes and C3/C4 clearance are separate order suffixes, not part of N206EA. Mass 205 g for the 30×62×16 mm N206EA execution covers the pressed-steel cage and full roller complement; substitute on mass plus rating, not envelope alone. After mounting verify the outer ring slides axially by hand at ambient temperature; a stuck float ring in a N206EA non-locating position preloads the bearing when the shaft grows.
Typical equipment & failure modes
Common applications
- material-handling drum and wheel shafts
- papermaking and printing auxiliary drives
- fan and blower rotor positions
- industrial gearbox input and output shafts
Known failure patterns
- inner-ring raceway spalling from overload in the line-contact Hertzian zone
- cage wear accelerated when the EA high-capacity roller complement runs continuously above its thermal balance
- grease starvation and cage drag when relubrication intervals are extended past the grease life
- fretting corrosion on a loose rotating shaft seat
- brinelling from static overload or impact during handling
Selection pitfalls — read before you substitute
- On this 30 mm bore, shaft thermal growth can preload the inner ring if the fit is too tight; verify residual interference at temperature and confirm the float ring still slides after mounting N206EA.
- Wide (22/23) and light (10/49) executions at 30 mm bore share bore but not OD/width; check the full N200 series code before substituting, because housing and shoulder geometry will not interchange.
- The EA high-capacity roller complement changes the load figure versus the basic execution of the same number; the 46/37.5 kN pair here belongs to N206EA as printed, not to the bare size.
- The 16.0 mm section at 30 mm bore leaves a narrow oil path; with the EA pressed-steel-cage cage the relubrication groove and oil-level design must keep grease from churning in the 16 mm-wide cavity.
- Never press either ring through the roller complement when fitting: mounting force goes through the ring faces, or the 62 mm race brinells and releases as vibration within hours.
- The 46/37.5 kN ratings, 4.55 kN Pu and 205 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for N206EA (EA pressed-steel-cage execution); other makes sharing the ISO 15 envelope revise internal geometry without changing the order number, so keep the 2203E reference with the specification for critical drives.
Frequently asked questions
What are the dimensions and catalogue data of N206EA?
N206EA is an NTN N single-row cylindrical roller bearing to ISO 15: 30 mm bore, 62 mm OD and 16 mm width (1.181 × 2.441 × 0.63 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 46 kN, C0 37.5 kN, Pu 4.55 kN, grease limiting speed 11,000 r/min, oil 15,600 r/min, mass about 205 g. It is open, with the EA high-capacity pressed sheet-steel cage.
What is the difference between NU, NJ, NUP, N and NF cylindrical roller bearings?
The prefix states the rib arrangement: NU has two outer-ring ribs and a ribless inner ring (float, no axial load); NJ adds ribs for one-direction location; NUP adds a loose L-ring to locate both directions; N has two inner-ring ribs and a separable outer ring; NF has one rib per ring for one-direction guidance. N206EA is two integral ribs on the inner ring and a ribless separable outer ring — equivalent float behaviour with the separable ring on the housing side.
What do the EA, E and ＊ suffixes mean on NTN cylindrical roller bearings?
EA is NTN's high-capacity design with a pressed sheet-steel cage and optimised roller complement in the same ISO 15 envelope; E marks the high-capacity design at the larger bores; the ＊ symbol printed before the code in the NTN catalogue marks the ULTAGE new-generation specification and is not typed as part of the order number. This page's bearing carries the EA pressed-steel-cage execution.
Can N206EA take axial load and locate a shaft?
the N design is non-locating like NU but floats with the separable outer ring in the housing. Provide axial location with an adjacent locating bearing (angular-contact, deep-groove or a paired NJ/NUP set).
What do Fw and Ew mean for N206EA?
Fw is the inner sub-assembly raceway/roller-set envelope diameter and Ew the outer-ring raceway diameter printed for geometric checks: Fw 37.5 mm, Ew 55.5 mm. The nominal bore/OD remain 30/62 mm; Fw/Ew describe the rolling-contact path, and speeds still run to 11,000 r/min grease / 15,600 r/min oil.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.