MPNbase

30×62×16 mm bearings

49 models from 4 brands across 6 types share this ISO 15 envelope: 30 mm bore, 62 mm outside diameter, 16 mm width (1.181×2.441×0.630 in), 16 mm radial section.

49 models fit this space 4 brands 49 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
11206-TN9 Self-Aligning Ball SKF open CN 15.6 4.65 350
1206 Self-Aligning Ball NTN open — 15.8 4.65 220
1206-EKTN9 Self-Aligning Ball SKF open CN 15.6 4.65 220
1206-ETN9 Self-Aligning Ball SKF open CN 15.6 4.65 220
1206K Self-Aligning Ball NTN open — 15.8 4.65 220
1726206-2RS1 Insert (Y-bearings) SKF 2RS CN 19.5 11.2 190
206 Deep Groove Ball SKF open CN 20.9 16.3 210
206-ZZ Deep Groove Ball SKF ZZ CN 20.9 16.3 210
6206 Deep Groove Ball SKF open CN 20.3 11.2 200
6206-2RS Deep Groove Ball SKF 2RS CN 20.3 11.2 210
6206-2RS-FAG Deep Groove Ball FAG 2RS CN 22 11.3 201
6206-2RS-NSK Deep Groove Ball NSK 2RS CN 21.4 11.3 199
6206-2RS-NTN Deep Groove Ball NTN 2RS CN 21.6 11.3 199
6206-FAG Deep Groove Ball FAG open CN 22 11.3 186
6206-NSK Deep Groove Ball NSK open CN 21.4 11.3 199
6206-NTN Deep Groove Ball NTN open CN 21.6 11.3 199
6206-RSR Deep Groove Ball SKF RSR CN 20.3 11.2 200
6206-RSR-NSK Deep Groove Ball NSK RSR CN 21.4 11.3 199
6206-RSR-NTN Deep Groove Ball NTN RSR CN 21.6 11.3 199
6206-ZZ Deep Groove Ball SKF ZZ CN 20.3 11.2 210
6206-ZZ-FAG Deep Groove Ball FAG ZZ CN 22 11.3 193
6206-ZZ-NSK Deep Groove Ball NSK ZZ CN 21.4 11.3 199
6206-ZZ-NTN Deep Groove Ball NTN ZZ CN 21.6 11.3 199
7206 Angular Contact Ball SKF open CN 22.5 14.3 200
7206-ACCBM Angular Contact Ball SKF open CN 27.5 17.3 200
7206-BE-2RZP Angular Contact Ball SKF RSR CN 22.5 14.3 260
7206-BECBM Angular Contact Ball SKF open CN 24 15.6 200
7206-BECBP Angular Contact Ball SKF open CN 24 15.6 200
7206-BECBPH Angular Contact Ball SKF open CN 24 15.6 200
7206-BECBY Angular Contact Ball SKF open CN 25.5 17 200
7206-BEP Angular Contact Ball SKF open CN 22.5 14.3 200
7206-NTN Angular Contact Ball NTN open CN 24.9 14.8 193
7206B Angular Contact Ball NTN open CN 22.7 13.5 197
BMD-6206-064S2-UA008A Sensor Bearing Units SKF — — 19.5 11.2 220
BMD-6206-064S2-UA108A Sensor Bearing Units SKF — — 19.5 11.2 240
N206-ECP Cylindrical Roller SKF open CN 44 36.5 200
N206EA Cylindrical Roller NTN open CN 46 37.5 205
NF206EA Cylindrical Roller NTN open CN 46 37.5 205
NJ206-ECP Cylindrical Roller SKF open CN 44 36.5 210
NJ206EA Cylindrical Roller NTN open CN 46 37.5 205
NU206 Cylindrical Roller SKF open CN 44 36.5 200
NU206EA Cylindrical Roller NTN open CN 46 37.5 205
NUP206-ECP Cylindrical Roller SKF open CN 44 36.5 210
NUP206EA Cylindrical Roller NTN open CN 46 37.5 205
QJ-206-MA Angular Contact Ball SKF open CN 37.5 30.5 240
QJ-206-N2MA Angular Contact Ball SKF open CN 37.5 30.5 240
W6206 Deep Groove Ball SKF open CN 16.5 11.2 186
W6206-2RS Deep Groove Ball SKF 2RS CN 16.5 11.2 196
W6206-ZZ Deep Groove Ball SKF ZZ CN 16.5 11.2 196

Note: catalogue dynamic load ratings for this envelope span 15.6– 46.0 kN — a 195% spread between designs in the very same 30×62×16 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 30 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 11206-TN9, 1206, 1206-EKTN9, 1206-ETN9, 1206K, 1726206-2RS1, 206, 206-ZZ, 6206, 6206-2RS, 6206-2RS-FAG, 6206-2RS-NSK, 6206-2RS-NTN, 6206-FAG, 6206-NSK, 6206-NTN, 6206-RSR, 6206-RSR-NSK, 6206-RSR-NTN, 6206-ZZ, 6206-ZZ-FAG, 6206-ZZ-NSK, 6206-ZZ-NTN, 7206, 7206-ACCBM, 7206-BE-2RZP, 7206-BECBM, 7206-BECBP, 7206-BECBPH, 7206-BECBY, 7206-BEP, 7206-NTN, 7206B, BMD-6206-064S2-UA008A, BMD-6206-064S2-UA108A, N206-ECP, N206EA, NF206EA, NJ206-ECP, NJ206EA, NU206, NU206EA, NUP206-ECP, NUP206EA, QJ-206-MA, QJ-206-N2MA, W6206, W6206-2RS, W6206-ZZ.

Frequently asked questions

Are all 30×62×16 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 30 mm bore, 62 mm OD, 16 mm width (1.181×2.441×0.630 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 49 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 30×62×16?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 30×62×16 mm in inches?

30×62×16 mm converts to 1.181×2.441×0.630 in, with a 16 mm (0.630 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 11206-TN9, 1206, 1206-EKTN9 mount in the same space despite different internal designs.