6206-RSR-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6206-RSR-NSK model number is decoded

6206-RSR uses two non-contact elastomer lips with very low drag; coarse debris stays out, but the bearing is not liquid-tight. Within the light 62xx section (diameter series 2 of ISO 15), multiplying bore code 06 by five gives the 30 mm bore; the 62 mm outside diameter and 16 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 30 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NSK's non-contact seal suffix is VV (catalogue number 6206VV), mapped here from the industry-neutral -RSR spelling; speed capability is close to the open bearing but VV is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Sizes around 30 mm bore are normally pressed on cold with a sleeve against the inner-ring face; the press force must never route through the outer ring or the balls of 6206-RSR-NSK.
• At 30 mm bore the 62xx light series is the workhorse section; its 62×16 mm envelope is what most motor and gearbox seats are machined for, so any alternative section must be checked against both this OD and this width, not the bore alone.
• The low-drag lip of 6206-RSR-NSK barely touches the inner ring; after long shelf storage the grease can separate, so rotate the rings by hand and confirm smooth, silent running before fitting.
• The non-contact lip of 6206-RSR-NSK does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 30 mm bore position before relying on it as sealed-for-life.
• Shaft and housing fillets must clear the bearing chamfer so the 16 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.
• Vibration during standstill brinells the raceways of a 30 mm bearing at ball spacing; if the machine sits idle next to running equipment, turn the shaft over periodically or isolate the arrangement.
• NSK catalogues this low-friction non-contact seal as 6206VV (suffix VV), mapped here from the industry-neutral -RSR spelling. NSK rates its speed capability close to the open bearing, but VV is not liquid-tight — for wet or fine-dust duty step up to the DDU contact seal (industry-neutral -2RS).
• The 30 mm bore puts 6206 in NSK's light industrial range; the standard pressed-steel cage and CN clearance cover most fractional-horsepower motor and small-pump duty. NSK's VV non-contact seal is the high-speed choice here — DDU contact seal costs roughly 30–40% of the open-bearing speed ceiling.
• At 21.4 kN dynamic load rating (C) and 11.3 kN static (C0), 6206 is a medium-load NSK bearing suitable for most electric-motor and pump duty; the C0/C0r ratio matters for preloaded or thrust-loaded arrangements, so confirm the static safety factor with the NSK catalogue.
• At 199 g, 6206 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 30×62×16 mm envelope of 6206 gives a D/d ratio of 2.07 and 16.0 mm radial section height — a heavy NSK section built for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 21.4/11.3 kN load ratings, mass 199 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6206VV on the 30×62×16 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6206 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• Keep NSK bearings in the original packaging until fitting: the wrapper carries the production lot, and the unopened shelf life of greased sealed units is typically quoted at three to five years in dry, vibration-free storage.
• Standard P0 runout from NSK is adequate up to the catalogue limiting speed on ground shaft seats; spindle or instrument positions should specify P6/P5 accuracy explicitly — it is a different order code, not a sorting of standard stock.