NU206EA bearing: complete specifications & equivalents
The NU206EA is a ISO 15 radial bearing sized 30 x 62 x 16 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 30 mm |
| Outer diameter D | 62 mm |
| Width B | 16 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 46 kN |
| Basic static load rating C0 | 37.5 kN |
| Fatigue load limit Pu | 4.55 kN |
| Limiting speed (mechanical) | 11000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 205 g |
| Manufacturer designation | NTN NU206EA |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & NU200-series range
| Bore d | 1.181 in |
|---|---|
| Outer diameter D | 2.441 in |
| Width B | 0.63 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 16 mm |
| Smallest bore in NU200-series | 15 mm |
| Largest outer diameter in NU200-series | 580 mm |
| Width range across NU200-series | 11–92 mm |
| Bore position in NU200-series (smallest first) | 5 of 36 |
| Bore above smallest NU200-series size | 15 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NU206EA | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NU206EA model number is decoded
NU206EA belongs to the NTN cylindrical roller range in NTN Ball and Roller Bearings CAT.No.2203E, under the ＊ ULTAGE new-generation specification: line-contact rollers between ground raceways for a 46 kN dynamic rating in the 30 mm bore. The leading NU defines the rib arrangement (outer ring ribbed, inner ring ribless); the dimension-series digits and the two-digit bore code resolve to 30 mm, with 62 mm OD and 16 mm width from the ISO 15 general plan. The 16.0 mm radial section ((62−30)/2) frames the roller complement; capacity per millimetre of bore is about 1.5 kN/mm before application factors. With the inner ring rotating, catalogue practice is a k5/m5 shaft seat and an H7/H6 housing; the outer ring must remain free to creep slightly axially in non-locating NU arrangements. Housing and shaft fillets must clear the ring chamfers of NU206EA; an oversized radius locks the ring on its face and tilts the 16 mm-wide seat.
Typical equipment & failure modes
Common applications
- fan and blower rotor positions
- industrial gearbox input and output shafts
- medium electric-motor and generator shafts
- pump and compressor crankshafts and rotors
Known failure patterns
- roller smearing (microwelding) at start-up before the oil film builds under insufficient radial load
- cage wear accelerated when the EA high-capacity roller complement runs continuously above its thermal balance
- roller-end and raceway scoring from inadequate oil flow under heavy radial load
- brinelling from static overload or impact during handling
- fretting corrosion on a loose rotating shaft seat
Selection pitfalls — read before you substitute
- On this 30 mm bore, shaft thermal growth can preload the inner ring if the fit is too tight; verify residual interference at temperature and confirm the float ring still slides after mounting NU206EA.
- Open NU206EA units need application-supplied sealing and a defined lubricant schedule; film thickness is the first failure mode for line contact when viscosity drops at the 30 mm contact.
- Wide (22/23) and light (10/49) executions at 30 mm bore share bore but not OD/width; check the full NU200 series code before substituting, because housing and shoulder geometry will not interchange.
- Never press either ring through the roller complement when fitting: mounting force goes through the ring faces, or the 62 mm race brinells and releases as vibration within hours.
- The 16.0 mm section at 30 mm bore leaves a narrow oil path; with the EA pressed-steel-cage cage the relubrication groove and oil-level design must keep grease from churning in the 16 mm-wide cavity.
- The 46/37.5 kN ratings, 4.55 kN Pu and 205 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for NU206EA (EA pressed-steel-cage execution); other makes sharing the ISO 15 envelope revise internal geometry without changing the order number, so keep the 2203E reference with the specification for critical drives.
Frequently asked questions
What are the dimensions and catalogue data of NU206EA?
NU206EA is an NTN NU single-row cylindrical roller bearing to ISO 15: 30 mm bore, 62 mm OD and 16 mm width (1.181 × 2.441 × 0.63 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 46 kN, C0 37.5 kN, Pu 4.55 kN, grease limiting speed 11,000 r/min, oil 15,600 r/min, mass about 205 g. It is open, with the EA high-capacity pressed sheet-steel cage.
What is the difference between NU, NJ, NUP, N and NF cylindrical roller bearings?
The prefix states the rib arrangement: NU has two outer-ring ribs and a ribless inner ring (float, no axial load); NJ adds ribs for one-direction location; NUP adds a loose L-ring to locate both directions; N has two inner-ring ribs and a separable outer ring; NF has one rib per ring for one-direction guidance. NU206EA is two integral ribs on the outer ring and a ribless, separable inner ring — a non-locating bearing that lets the shaft float axially.
What do the EA, E and ＊ suffixes mean on NTN cylindrical roller bearings?
EA is NTN's high-capacity design with a pressed sheet-steel cage and optimised roller complement in the same ISO 15 envelope; E marks the high-capacity design at the larger bores; the ＊ symbol printed before the code in the NTN catalogue marks the ULTAGE new-generation specification and is not typed as part of the order number. This page's bearing carries the EA pressed-steel-cage execution.
Can NU206EA take axial load and locate a shaft?
the NU design carries no axial load and floats axially on both sides. Provide axial location with an adjacent locating bearing (angular-contact, deep-groove or a paired NJ/NUP set).
What do Fw and Ew mean for NU206EA?
Fw is the inner sub-assembly raceway/roller-set envelope diameter and Ew the outer-ring raceway diameter printed for geometric checks: Fw 37.5 mm, Ew 55.5 mm. The nominal bore/OD remain 30/62 mm; Fw/Ew describe the rolling-contact path, and speeds still run to 11,000 r/min grease / 15,600 r/min oil.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.