NCF2230-ECJB bearing: complete specifications & equivalents
The NCF2230-ECJB is a ISO 15 radial bearing sized 150 x 270 x 73 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 150 mm |
| Outer diameter D | 270 mm |
| Width B | 73 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 780 kN |
| Basic static load rating C0 | 1040 kN |
| Fatigue load limit Pu | 112 kN |
| Reference speed (thermal) | 2600 rpm |
| Limiting speed (mechanical) | 3400 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 18000 g |
| Manufacturer designation | SKF NCF 2230 ECJB |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.2 high-capacity cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.2 high-capacity cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.2 high-capacity cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NCF2200-series range
| Bore d | 5.906 in |
|---|---|
| Outer diameter D | 10.63 in |
| Width B | 2.874 in |
| ISO bore code | 30 |
| Radial section height (D−d)/2 | 60 mm |
| Smallest bore in NCF2200-series | 120 mm |
| Largest outer diameter in NCF2200-series | 400 mm |
| Width range across NCF2200-series | 58–108 mm |
| Bore position in NCF2200-series (smallest first) | 3 of 9 |
| Bore above smallest NCF2200-series size | 30 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NUH2230-ECMH | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 150×270×73 mm and equivalent catalogue ratings; the NUH execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NCF2230-ECJB model number is decoded
NCF2230-ECJB is the 150 mm bore entry in the NCF2200 range: a 150×270×73 mm high-capacity cylindrical roller bearing with a pressed sheet-steel window-type cage, rated C 780 kN / C0 1040 kN. The NCF configuration means the high-capacity caged partner execution (ECJB pressed-steel cages with displaced cage bars for extra rollers), matching the NUH bearing in the same dimension envelope; functionally the bearing is the non-locating member of the paired high-capacity arrangement, absorbing axial displacement while carrying the full high radial rating. Reading the order-string suffix ECJB: the high-capacity execution with pressed-steel cages (the /PEX mark denotes the pinion-shaft special build with its own catalogue rating line). Speed planning for NCF2230-ECJB: the catalogue lists 2,600 r/min thermal reference speed and 3,400 r/min mechanical limiting speed. The mass entry 18000 g covers the complete catalogue execution. Assembly note: used opposite the NUH locating bearing on wind-gearbox and heavy industrial pinion shafts; fit the inner ring with interference and let this bearing float axially. Heat steel rings inductively to max 120 °C. This is the standard catalogue execution of the high-capacity design. Selected sizes in the range are also produced as /PEX pinion-shaft builds for wind-turbine gearboxes — separate order numbers with their own rating lines and internal profiling; the two must not be mixed using one another’s loads.
Typical equipment & failure modes
Common applications
- multi-megawatt wind turbine main gearboxes
- offshore and marine heavy drive trains
- large mining mill pinion shafts
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- micro-pitting on the profiled rollers under contaminated or starved-lubricant conditions despite the black-oxide treatment
- polymer cage cracking or softening after sustained running above 120 °C or with incompatible lubricant
- roller-end scoring from inadequate oil flow in the roller-raceway contact
- cage fatigue in heavily reversing wind-turbine load cycles when relubrication intervals are exceeded
- smearing (microwelding) on roller surfaces during skid starts with insufficient minimum load
Selection pitfalls — read before you substitute
- High-capacity NUH and NCF bearings are designed as a locating/non-locating PAIR on the same shaft; fitting two locating NUH bearings can preload the arrangement thermally.
- The /PEX pinion execution carries its own rating line and internal geometry — never substitute a standard NCF 2230 using the /PEX loads.
- Press-fit force goes through ring faces only; driving a ring home through the rollers brinells the 270 mm raceway.
- Shaft and housing fillets must clear the bearing chamfers; an oversized radius tilts the 73 mm-wide ring and concentrates load.
- The 780/1040 kN ratings are SKF catalogue 17000 (2018) values for the ECJB execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NCF2230-ECJB?
SKF NCF 2230 ECJB is a high-capacity cylindrical roller bearing with 150 mm bore, 270 mm OD and 73 mm width per ISO 15. SKF lists C 780 kN, C0 1040 kN, Pu 112 kN, reference speed 2,600 r/min and limiting speed 3,400 r/min, mass about 18000 g.
What does the NCF designation and ECJB suffix mean?
The ECJB suffix denotes the high-capacity execution with pressed-steel cages; /PEX marks the pinion-shaft special build with its own catalogue rating line. Structurally this execution has the high-capacity caged partner execution (ECJB pressed-steel cages with displaced cage bars for extra rollers), matching the NUH bearing in the same dimension envelope.
Can NCF2230-ECJB take axial load and locate the shaft?
The high-capacity NCF ECJB execution is the non-locating partner in the NUH/NCF pair and should float axially.
How does NCF2230-ECJB compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.2 high-capacity cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.