NF315 bearing: complete specifications & equivalents
The NF315 is a ISO 15 radial bearing sized 75 x 160 x 37 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 75 mm |
| Outer diameter D | 160 mm |
| Width B | 37 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 211 kN |
| Basic static load rating C0 | 205 kN |
| Fatigue load limit Pu | 23.8 kN |
| Limiting speed (mechanical) | 4400 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 3210 g |
| Manufacturer designation | NTN NF315 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & NF300-series range
| Bore d | 2.953 in |
|---|---|
| Outer diameter D | 6.299 in |
| Width B | 1.457 in |
| ISO bore code | 15 |
| Radial section height (D−d)/2 | 42.5 mm |
| Smallest bore in NF300-series | 20 mm |
| Largest outer diameter in NF300-series | 580 mm |
| Width range across NF300-series | 15–108 mm |
| Bore position in NF300-series (smallest first) | 12 of 32 |
| Bore above smallest NF300-series size | 55 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NF315 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NF315 model number is decoded
NF315 belongs to the NTN cylindrical roller range in NTN Ball and Roller Bearings CAT.No.2203E, under the ＊ ULTAGE new-generation specification: line-contact rollers between ground raceways for a 211 kN dynamic rating in the 75 mm bore. Digit by digit, NF315 reads as NF (one rib on each ring), ISO 15 series, and bore 75 mm; trailing letters such as EA or E mark the cage/capacity execution and are part of the order number. the bare number is the standard-capacity open execution with the normal pressed-steel cage; the ＊ symbol printed before the number in 2203E marks the ULTAGE new-generation specification — upgraded material/geometry and longer rating life, not part of the order code; quote the full NF315 designation when purchasing. Equivalent-load planning treats NF315 as a pure radial bearing: keep P below 211 kN at the required L10, and let a paired angular-contact or thrust part carry any sustained axial component. Mount the separable inner ring + roller assembly on the shaft first and slide the outer ring into the housing; never press the outer ring through the rollers of NF315.
Typical equipment & failure modes
Common applications
- heavy industrial gearbox and reducer shafts
- large pump, turbine and compressor rotors
- rolling-mill auxiliary drive shafts
- crusher and vibrating-screen drive shafts
Known failure patterns
- inner-ring raceway spalling from overload in the line-contact Hertzian zone
- pressed-steel cage pocket wear when rollers skid at light load or too-thin lubricant
- micro-pitting when the EHL film falls below the composite roughness at high specific load
- hard-particle indentation of raceways in unfiltered oil or open arrangements
- false brinelling on standby machines exposed to external vibration
Selection pitfalls — read before you substitute
- Induction-heat the 75 mm inner ring (max 120 °C) and mount it before fitting the outer ring; the ring mass makes square guidance essential — driving through the rollers brinells the 160 mm raceway.
- Never press either ring through the roller complement when fitting: mounting force goes through the ring faces, or the 160 mm race brinells and releases as vibration within hours.
- Do not replace NF315 with a deep-groove ball bearing on rating alone: line contact gives 211 kN radial capacity but the bearing cannot carry the thrust duty a ball bearing can and misalignment tolerance is only 3–4 arc-minutes.
- Wide (22/23) and light (10/49) executions at 75 mm bore share bore but not OD/width; check the full NF300 series code before substituting, because housing and shoulder geometry will not interchange.
- The 37 mm width and abutment faces must be square to the axis; a tilted spacer concentrates load across the roller set and shows as uneven raceway polish on the 75 mm inner ring.
- The 211/205 kN ratings, 23.8 kN Pu and 3210 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for NF315 (standard execution); other makes sharing the ISO 15 envelope revise internal geometry without changing the order number, so keep the 2203E reference with the specification for critical drives.
Frequently asked questions
What are the dimensions and catalogue data of NF315?
NF315 is an NTN NF single-row cylindrical roller bearing to ISO 15: 75 mm bore, 160 mm OD and 37 mm width (2.953 × 6.299 × 1.457 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 211 kN, C0 205 kN, Pu 23.8 kN, grease limiting speed 4,400 r/min, oil 5,200 r/min, mass about 3210 g. It is open, with a pressed sheet-steel cage.
What is the difference between NU, NJ, NUP, N and NF cylindrical roller bearings?
The prefix states the rib arrangement: NU has two outer-ring ribs and a ribless inner ring (float, no axial load); NJ adds ribs for one-direction location; NUP adds a loose L-ring to locate both directions; N has two inner-ring ribs and a separable outer ring; NF has one rib per ring for one-direction guidance. NF315 is one integral rib on each ring — separable inner ring with single-direction axial guidance and a defined shaft position.
What do the EA, E and ＊ suffixes mean on NTN cylindrical roller bearings?
EA is NTN's high-capacity design with a pressed sheet-steel cage and optimised roller complement in the same ISO 15 envelope; E marks the high-capacity design at the larger bores; the ＊ symbol printed before the code in the NTN catalogue marks the ULTAGE new-generation specification and is not typed as part of the order number. NF315 is listed among the ＊ ULTAGE-marked executions in 2203E.
Can NF315 take axial load and locate a shaft?
the NF design gives one-direction axial guidance via its single outer-ring rib. The loose rib ring still only suits light/short-duration axial guidance; heavy thrust belongs to a dedicated thrust bearing.
What do Fw and Ew mean for NF315?
Fw is the inner sub-assembly raceway/roller-set envelope diameter and Ew the outer-ring raceway diameter printed for geometric checks: Fw 95.5 mm, Ew 139.5 mm. The nominal bore/OD remain 75/160 mm; Fw/Ew describe the rolling-contact path, and speeds still run to 4,400 r/min grease / 5,200 r/min oil.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.