NF315EA bearing: complete specifications & equivalents
The NF315EA is a ISO 15 radial bearing sized 75 x 160 x 37 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 75 mm |
| Outer diameter D | 160 mm |
| Width B | 37 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 284 kN |
| Basic static load rating C0 | 263 kN |
| Fatigue load limit Pu | 30.5 kN |
| Limiting speed (mechanical) | 4000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 3280 g |
| Manufacturer designation | NTN NF315EA |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & NF300-series range
| Bore d | 2.953 in |
|---|---|
| Outer diameter D | 6.299 in |
| Width B | 1.457 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 42.5 mm |
| Smallest bore in NF300-series | 20 mm |
| Largest outer diameter in NF300-series | 580 mm |
| Width range across NF300-series | 15–108 mm |
| Bore position in NF300-series (smallest first) | 12 of 32 |
| Bore above smallest NF300-series size | 55 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NF315EA | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NF315EA model number is decoded
For pure radial duty on a 75 mm shaft NTN supplies NF315EA: one integral rib on each ring; the open execution is rated 4,000 r/min on grease and 5,600 r/min on oil. On the NTN nameplate NF states which ring carries the ribs, which determines whether NF315EA floats or locates; the numeric remainder is the ISO 15 series and 75 mm bore reference, not a fit or clearance instruction. NTN ships these bearings open with normal (CN) radial clearance and P0 tolerance as standard; precision classes and C3/C4 clearance are separate order suffixes, not part of NF315EA. With the inner ring rotating, catalogue practice is a k5/m5 shaft seat and an H7/H6 housing; the outer ring must remain free to creep slightly axially in non-locating NF arrangements. On NF arrangements confirm which ring is separable before heating: forcing the ribbed ring off over the roller complement damages the cage and rib faces.
Typical equipment & failure modes
Common applications
- rolling-mill auxiliary drive shafts
- crusher and vibrating-screen drive shafts
- marine gearbox and deck-machinery shafts
- large electric-motor and generator rotors
Known failure patterns
- roller smearing (microwelding) at start-up before the oil film builds under insufficient radial load
- cage wear accelerated when the EA high-capacity roller complement runs continuously above its thermal balance
- micro-pitting when the EHL film falls below the composite roughness at high specific load
- false brinelling on standby machines exposed to external vibration
- edge loading from shaft deflection beyond the 3–4 arc-minute alignment limit
Selection pitfalls — read before you substitute
- Induction-heat the 75 mm inner ring (max 120 °C) and mount it before fitting the outer ring; the ring mass makes square guidance essential — driving through the rollers brinells the 160 mm raceway.
- Grease limiting speed 4,000 r/min and oil 5,600 r/min are different limits for NF315EA: the first is the cage/lubricant mechanical ceiling, the second assumes real oil flow rather than an oil bath.
- The NF rib arrangement is not interchangeable with another prefix on the same 75 mm seat: one rib on each ring. Swapping NU for NJ changes axial location behaviour even though the 160×37 mm envelope matches.
- Never press either ring through the roller complement when fitting: mounting force goes through the ring faces, or the 160 mm race brinells and releases as vibration within hours.
- Never press either ring through the roller complement when fitting: mounting force goes through the ring faces, or the 160 mm race brinells and releases as vibration within hours.
- The 284/263 kN ratings, 30.5 kN Pu and 3280 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for NF315EA (EA pressed-steel-cage execution); other makes sharing the ISO 15 envelope revise internal geometry without changing the order number, so keep the 2203E reference with the specification for critical drives.
Frequently asked questions
What are the dimensions and catalogue data of NF315EA?
NF315EA is an NTN NF single-row cylindrical roller bearing to ISO 15: 75 mm bore, 160 mm OD and 37 mm width (2.953 × 6.299 × 1.457 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 284 kN, C0 263 kN, Pu 30.5 kN, grease limiting speed 4,000 r/min, oil 5,600 r/min, mass about 3280 g. It is open, with the EA high-capacity pressed sheet-steel cage.
What is the difference between NU, NJ, NUP, N and NF cylindrical roller bearings?
The prefix states the rib arrangement: NU has two outer-ring ribs and a ribless inner ring (float, no axial load); NJ adds ribs for one-direction location; NUP adds a loose L-ring to locate both directions; N has two inner-ring ribs and a separable outer ring; NF has one rib per ring for one-direction guidance. NF315EA is one integral rib on each ring — separable inner ring with single-direction axial guidance and a defined shaft position.
What do the EA, E and ＊ suffixes mean on NTN cylindrical roller bearings?
EA is NTN's high-capacity design with a pressed sheet-steel cage and optimised roller complement in the same ISO 15 envelope; E marks the high-capacity design at the larger bores; the ＊ symbol printed before the code in the NTN catalogue marks the ULTAGE new-generation specification and is not typed as part of the order number. This page's bearing carries the EA pressed-steel-cage execution.
Can NF315EA take axial load and locate a shaft?
the NF design gives one-direction axial guidance via its single outer-ring rib. The loose rib ring still only suits light/short-duration axial guidance; heavy thrust belongs to a dedicated thrust bearing.
What do Fw and Ew mean for NF315EA?
Fw is the inner sub-assembly raceway/roller-set envelope diameter and Ew the outer-ring raceway diameter printed for geometric checks: Fw 95 mm, Ew 143 mm. The nominal bore/OD remain 75/160 mm; Fw/Ew describe the rolling-contact path, and speeds still run to 4,000 r/min grease / 5,600 r/min oil.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.