NJ1060-MA bearing: complete specifications & equivalents
The NJ1060-MA is a ISO 15 radial bearing sized 300 x 460 x 74 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 300 mm |
| Outer diameter D | 460 mm |
| Width B | 74 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass |
| Basic dynamic load rating C | 858 kN |
| Basic static load rating C0 | 1370 kN |
| Fatigue load limit Pu | 129 kN |
| Reference speed (thermal) | 1500 rpm |
| Limiting speed (mechanical) | 2000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 46000 g |
| Manufacturer designation | SKF NJ 1060 MA |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NJ1000-series range
| Bore d | 11.811 in |
|---|---|
| Outer diameter D | 18.11 in |
| Width B | 2.913 in |
| ISO bore code | 60 |
| Radial section height (D−d)/2 | 80 mm |
| Smallest bore in NJ1000-series | 45 mm |
| Largest outer diameter in NJ1000-series | 600 mm |
| Width range across NJ1000-series | 16–90 mm |
| Bore position in NJ1000-series (smallest first) | 12 of 15 |
| Bore above smallest NJ1000-series size | 255 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NU1060-MA | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 300×460×74 mm and equivalent catalogue ratings; the NU execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NJ1060-MA model number is decoded
For a 300 mm shaft, SKF lists NJ1060-MA as single-row caged cylindrical roller: 460 mm OD, 74 mm wide, Pu 129 kN, the catalogue lists 1,500 r/min thermal reference speed and 2,000 r/min mechanical limiting speed. Reading the NJ prefix: two integral flanges on the inner ring and no flanges on the outer ring; the inner ring retains the roller set. This makes the execution able to locate the shaft axially in one direction; an HJ angle ring on the opposite side converts it into two-direction location. The MA suffix marks the basic (non-E) execution with a machined brass cage, the standard choice for the larger and earlier-design sizes. The one-piece machined brass cage is reflected in the published speeds and temperature limits. The radial section height is 80.0 mm and the catalogue mass 46000 g; at 858 kN dynamic rating this is roughly 2.86 kN of C per millimetre of bore before application factors. Fit practice for NJ1060-MA: orient the inner-ring flange side toward the axial load direction; if an HJ angle ring is used, verify its fit and clearance before locking the arrangement. Single-row cylindrical rollers tolerate only about 3–4 minutes of arc misalignment, so verify shaft and housing alignment.
Typical equipment & failure modes
Common applications
- marine propulsion line shafts
- heavy turbogenerator rotor supports
- mining hoist and winder shafts
- offshore drawworks shafts
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- cage pocket wear from roller skew at light load
- cage pocket wear from roller skidding at insufficient radial load or during start-up before oil film build-up
- roller-end scoring from inadequate oil flow in the roller-raceway contact
- edge-loading fatigue after shaft deflection beyond the 3–4 minute alignment limit
- electrical pitting on VFD-driven shafts without grounding protection
Selection pitfalls — read before you substitute
- Do not use a NJ bearing where two-direction axial location is required without an HJ angle ring
- The dimension series 10 (extra-slim OD, normal width) envelope is shared with the N/NU/NJ/NUP executions of 1060, but flange configuration and axial-locating behaviour differ — quote the full SKF NJ 1060 MA and do not substitute rib styles without checking the shaft locating scheme.
- Shaft and housing fillets must clear the bearing chamfers; an oversized radius tilts the 74 mm-wide ring and concentrates load.
- Catalogue reference and limiting speeds are different criteria: observe the mechanical ceiling even when thermal calculations allow more.
- The 858/1370 kN ratings are SKF catalogue 17000 (2018) values for the MA execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NJ1060-MA?
SKF NJ 1060 MA is a single-row caged cylindrical roller bearing with 300 mm bore, 460 mm OD and 74 mm width per ISO 15. SKF lists C 858 kN, C0 1370 kN, Pu 129 kN, reference speed 1,500 r/min and limiting speed 2,000 r/min, mass about 46000 g.
What does the NJ designation and MA suffix mean?
The MA suffix marks the basic (non-E) execution with a machined brass cage, the standard choice for the larger and earlier-design sizes. Structurally this execution has two integral flanges on the inner ring and no flanges on the outer ring; the inner ring retains the roller set.
Can NJ1060-MA take axial load and locate the shaft?
In one direction only, via the two inner-ring flanges. Add an HJ angle ring on the opposite side for two-direction location.
How does NJ1060-MA compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.