NJ2326-ECML bearing: complete specifications & equivalents
The NJ2326-ECML is a ISO 15 radial bearing sized 130 x 280 x 93 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 130 mm |
| Outer diameter D | 280 mm |
| Width B | 93 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass |
| Basic dynamic load rating C | 1060 kN |
| Basic static load rating C0 | 1250 kN |
| Fatigue load limit Pu | 137 kN |
| Reference speed (thermal) | 2400 rpm |
| Limiting speed (mechanical) | 4500 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 29500 g |
| Manufacturer designation | SKF NJ 2326 ECML |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NJ2300-series range
| Bore d | 5.118 in |
|---|---|
| Outer diameter D | 11.024 in |
| Width B | 3.661 in |
| ISO bore code | 26 |
| Radial section height (D−d)/2 | 75 mm |
| Smallest bore in NJ2300-series | 20 mm |
| Largest outer diameter in NJ2300-series | 540 mm |
| Width range across NJ2300-series | 21–165 mm |
| Bore position in NJ2300-series (smallest first) | 20 of 28 |
| Bore above smallest NJ2300-series size | 110 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NU2326-ECML | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 130×280×93 mm and equivalent catalogue ratings; the NU execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
| NUP2326-ECML | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 130×280×93 mm and equivalent catalogue ratings; the NUP execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NJ2326-ECML model number is decoded
Ordering number SKF NJ 2326 ECML resolves to a 130×280×93 mm single-row caged cylindrical roller bearing (dimension series 23 (medium-section, wide)); two integral flanges on the inner ring and no flanges on the outer ring; the inner ring retains the roller set. The NJ configuration means two integral flanges on the inner ring and no flanges on the outer ring; the inner ring retains the roller set; functionally the bearing is able to locate the shaft axially in one direction; an HJ angle ring on the opposite side converts it into two-direction location. The ECML suffix denotes the E-design execution with a one-piece machined brass cage for higher-temperature and higher-speed continuous duty. With C 1060 kN and C0 1250 kN, size the bearing on the 130×280 mm ISO 15 envelope and check the 137 kN Pu against the equivalent-load floor; the catalogue lists 2,400 r/min thermal reference speed and 4,500 r/min mechanical limiting speed. Fit practice for NJ2326-ECML: orient the inner-ring flange side toward the axial load direction; if an HJ angle ring is used, verify its fit and clearance before locking the arrangement. Single-row cylindrical rollers tolerate only about 3–4 minutes of arc misalignment, so verify shaft and housing alignment.
Typical equipment & failure modes
Common applications
- heavy turbogenerator rotor supports
- mining hoist and winder shafts
- offshore drawworks shafts
- large rolling-mill drive trains
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- cage pocket wear from roller skew at light load
- cage pocket wear from roller skidding at insufficient radial load or during start-up before oil film build-up
- roller-end scoring from inadequate oil flow in the roller-raceway contact
- edge-loading fatigue after shaft deflection beyond the 3–4 minute alignment limit
- fretting corrosion on a loose rotating shaft seat or in a vibratory stand-still
Selection pitfalls — read before you substitute
- Do not use a NJ bearing where two-direction axial location is required without an HJ angle ring
- The dimension series 23 (medium-section, wide) envelope is shared with the N/NU/NJ/NUP executions of 2326, but flange configuration and axial-locating behaviour differ — quote the full SKF NJ 2326 ECML and do not substitute rib styles without checking the shaft locating scheme.
- Press-fit force goes through ring faces only; driving a ring home through the rollers brinells the 280 mm raceway.
- Shaft and housing fillets must clear the bearing chamfers; an oversized radius tilts the 93 mm-wide ring and concentrates load.
- The 1060/1250 kN ratings are SKF catalogue 17000 (2018) values for the ECML execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NJ2326-ECML?
SKF NJ 2326 ECML is a single-row caged cylindrical roller bearing with 130 mm bore, 280 mm OD and 93 mm width per ISO 15. SKF lists C 1060 kN, C0 1250 kN, Pu 137 kN, reference speed 2,400 r/min and limiting speed 4,500 r/min, mass about 29500 g.
What does the NJ designation and ECML suffix mean?
The ECML suffix denotes the E-design execution with a one-piece machined brass cage for higher-temperature and higher-speed continuous duty. Structurally this execution has two integral flanges on the inner ring and no flanges on the outer ring; the inner ring retains the roller set.
Can NJ2326-ECML take axial load and locate the shaft?
In one direction only, via the two inner-ring flanges. Add an HJ angle ring on the opposite side for two-direction location.
How does NJ2326-ECML compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.