NU2326-ECML bearing: complete specifications & equivalents
The NU2326-ECML is a ISO 15 radial bearing sized 130 x 280 x 93 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 130 mm |
| Outer diameter D | 280 mm |
| Width B | 93 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass |
| Basic dynamic load rating C | 1060 kN |
| Basic static load rating C0 | 1250 kN |
| Fatigue load limit Pu | 137 kN |
| Reference speed (thermal) | 2400 rpm |
| Limiting speed (mechanical) | 4500 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 28500 g |
| Manufacturer designation | SKF NU 2326 ECML |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NU2300-series range
| Bore d | 5.118 in |
|---|---|
| Outer diameter D | 11.024 in |
| Width B | 3.661 in |
| ISO bore code | 26 |
| Radial section height (D−d)/2 | 75 mm |
| Smallest bore in NU2300-series | 20 mm |
| Largest outer diameter in NU2300-series | 750 mm |
| Width range across NU2300-series | 21–224 mm |
| Bore position in NU2300-series (smallest first) | 20 of 35 |
| Bore above smallest NU2300-series size | 110 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NJ2326-ECML | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 130×280×93 mm and equivalent catalogue ratings; the NJ execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
| NUP2326-ECML | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 130×280×93 mm and equivalent catalogue ratings; the NUP execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NU2326-ECML model number is decoded
NU2326-ECML is the 130 mm bore entry in the NU2300 range: a 130×280×93 mm single-row caged cylindrical roller bearing with a one-piece machined brass cage, rated C 1060 kN / C0 1250 kN. Structurally, the NU design has two integral flanges on the outer ring and no flanges on the inner ring, so the inner ring together with the roller set is separable. In arrangement terms it is non-locating: the inner ring assembly can float axially in both directions and the bearing cannot support axial load. Reading the order-string suffix ECML: the E-design ECML execution with a one-piece machined brass cage for higher-temperature, higher-speed continuous duty. Load-per-bore for the 130 mm seat is about 8.15 kN/mm, typical of dimension series 23 (medium-section, wide); use C0 1250 kN for static checks such as crane hook blocks standing under load. Assembly note: fit the inner ring and roller assembly onto the shaft and the outer ring into the housing independently; thermal expansion is absorbed by axial float, so do not trap the inner ring between shaft shoulders. Heat steel rings inductively to max 120 °C.
Typical equipment & failure modes
Common applications
- offshore drawworks shafts
- large rolling-mill drive trains
- marine propulsion line shafts
- heavy turbogenerator rotor supports
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- cage pocket wear from roller skew at light load
- polymer cage cracking or softening after sustained running above 120 °C or with incompatible lubricant
- roller-end scoring from inadequate oil flow in the roller-raceway contact
- edge-loading fatigue after shaft deflection beyond the 3–4 minute alignment limit
- false brinelling on standby machines exposed to external vibration
Selection pitfalls — read before you substitute
- Do not use a NU bearing where axial load must be carried — the design carries radial load only
- The dimension series 23 (medium-section, wide) envelope is shared with the N/NU/NJ/NUP executions of 2326, but flange configuration and axial-locating behaviour differ — quote the full SKF NU 2326 ECML and do not substitute rib styles without checking the shaft locating scheme.
- Catalogue reference and limiting speeds are different criteria: observe the mechanical ceiling even when thermal calculations allow more.
- Shaft and housing fillets must clear the bearing chamfers; an oversized radius tilts the 93 mm-wide ring and concentrates load.
- The 1060/1250 kN ratings are SKF catalogue 17000 (2018) values for the ECML execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NU2326-ECML?
SKF NU 2326 ECML is a single-row caged cylindrical roller bearing with 130 mm bore, 280 mm OD and 93 mm width per ISO 15. SKF lists C 1060 kN, C0 1250 kN, Pu 137 kN, reference speed 2,400 r/min and limiting speed 4,500 r/min, mass about 28500 g.
What does the NU designation and ECML suffix mean?
The ECML suffix denotes the E-design execution with a one-piece machined brass cage for higher-temperature and higher-speed continuous duty. Structurally this execution has two integral flanges on the outer ring and no flanges on the inner ring, so the inner ring together with the roller set is separable.
Can NU2326-ECML take axial load and locate the shaft?
No — the inner ring has no flanges, so the NU bearing is non-locating and carries radial load only; use NJ (one direction), NUP (both directions) or a paired thrust bearing for axial duty.
How does NU2326-ECML compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.