NJ2328E bearing: complete specifications & equivalents
The NJ2328E is a ISO 15 radial bearing sized 140 x 300 x 102 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 140 mm |
| Outer diameter D | 300 mm |
| Width B | 102 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 1130 kN |
| Basic static load rating C0 | 1380 kN |
| Fatigue load limit Pu | 133 kN |
| Limiting speed (mechanical) | 1800 rpm |
| Operating temperature | -40 to +120 °C |
| Manufacturer designation | NTN NJ2328E |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & NJ2300-series range
| Bore d | 5.512 in |
|---|---|
| Outer diameter D | 11.811 in |
| Width B | 4.016 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 80 mm |
| Smallest bore in NJ2300-series | 20 mm |
| Largest outer diameter in NJ2300-series | 580 mm |
| Width range across NJ2300-series | 21–175 mm |
| Bore position in NJ2300-series (smallest first) | 21 of 31 |
| Bore above smallest NJ2300-series size | 120 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NJ2328E | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NJ2328E model number is decoded
The NTN order number NJ2328E denotes a 140×300×102 mm (5.512 × 11.811 × 4.016 in) cylindrical roller bearing in the NJ2300 family, the high-capacity pressed-steel cage of the E execution. On the NTN nameplate NJ states which ring carries the ribs, which determines whether NJ2328E floats or locates; the numeric remainder is the ISO 15 series and 140 mm bore reference, not a fit or clearance instruction. With C 1130 kN and C0 1380 kN (C0/C ≈ 1.22) the bearing is proportioned for heavy radial load; the NJ design accepts axial load in one direction and provides one-way shaft location. Mass Dimensions 140×300×102 mm and the 1130 kN C rating define the substitution envelope; check the 2203E mass column for this exact NJ2328E execution. Mount the separable inner ring + roller assembly on the shaft first and slide the outer ring into the housing; never press the outer ring through the rollers of NJ2328E.
Typical equipment & failure modes
Common applications
- wind-turbine gearbox planet and rotor shafts
- ship propulsion line shafts and reduction gears
- mining SAG/ball-mill drive shafts
- offshore drawworks and winch drums
Known failure patterns
- inner-ring raceway spalling from overload in the line-contact Hertzian zone
- cage wear accelerated when the EA high-capacity roller complement runs continuously above its thermal balance
- grease starvation and cage drag when relubrication intervals are extended past the grease life
- fretting corrosion on a loose rotating shaft seat
- fretting corrosion on a loose rotating shaft seat
Selection pitfalls — read before you substitute
- At 140 mm bore, oil-lubricated arrangements toward 2,100 r/min need positive flow and drain design; the NJ2328E ring stores enough heat that grease-only duty needs a careful relubrication calculation.
- The NJ rib arrangement is not interchangeable with another prefix on the same 140 mm seat: inner ring two ribs + one outer rib. Swapping NU for NJ changes axial location behaviour even though the 300×102 mm envelope matches.
- Do not replace NJ2328E with a deep-groove ball bearing on rating alone: line contact gives 1130 kN radial capacity but the bearing cannot carry the thrust duty a ball bearing can and misalignment tolerance is only 3–4 arc-minutes.
- The NJ rib arrangement is not interchangeable with another prefix on the same 140 mm seat: inner ring two ribs + one outer rib. Swapping NU for NJ changes axial location behaviour even though the 300×102 mm envelope matches.
- Minimum radial load is frequently missed in oversized motor and fan selections: an underloaded NJ2328E skids at 1,800 r/min and fails by smearing long before L10 fatigue.
- The 1130/1380 kN ratings, 133 kN Pu are NTN Ball and Roller Bearings CAT.No.2203E values for NJ2328E (E high-capacity execution); other makes sharing the ISO 15 envelope revise internal geometry without changing the order number, so keep the 2203E reference with the specification for critical drives.
Frequently asked questions
What are the dimensions and catalogue data of NJ2328E?
NJ2328E is an NTN NJ single-row cylindrical roller bearing to ISO 15: 140 mm bore, 300 mm OD and 102 mm width (5.512 × 11.811 × 4.016 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 1130 kN, C0 1380 kN, Pu 133 kN, grease limiting speed 1,800 r/min, oil 2,100 r/min. It is open, with the high-capacity pressed-steel cage of the E execution.
What is the difference between NU, NJ, NUP, N and NF cylindrical roller bearings?
The prefix states the rib arrangement: NU has two outer-ring ribs and a ribless inner ring (float, no axial load); NJ adds ribs for one-direction location; NUP adds a loose L-ring to locate both directions; N has two inner-ring ribs and a separable outer ring; NF has one rib per ring for one-direction guidance. NJ2328E is two integral ribs on the inner ring and one rib on the outer ring — it locates the shaft in one axial direction.
What do the EA, E and ＊ suffixes mean on NTN cylindrical roller bearings?
EA is NTN's high-capacity design with a pressed sheet-steel cage and optimised roller complement in the same ISO 15 envelope; E marks the high-capacity design at the larger bores; the ＊ symbol printed before the code in the NTN catalogue marks the ULTAGE new-generation specification and is not typed as part of the order number. NJ2328E is supplied in the standard open execution shown in the table.
Can NJ2328E take axial load and locate a shaft?
the NJ design accepts axial load in one direction and provides one-way shaft location. For two-direction location use an NUP execution or an NJ pair with loose rib rings.
What do Fw and Ew mean for NJ2328E?
Fw is the inner sub-assembly raceway/roller-set envelope diameter and Ew the outer-ring raceway diameter printed for geometric checks: Fw 180 mm. The nominal bore/OD remain 140/300 mm; Fw/Ew describe the rolling-contact path, and speeds still run to 1,800 r/min grease / 2,100 r/min oil.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.