140×300×102 mm bearings

20 models from 3 brands across 2 types share this ISO 15 envelope: 140 mm bore, 300 mm outside diameter, 102 mm width (5.512×11.811×4.016 in), 80 mm radial section.

20 models fit this space 3 brands 20 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
22328 Spherical Roller SKF open CN 1357 1560 36500
22328-CCK-W33 Spherical Roller SKF open CN 1357 1560 41000
22328EAD1 Spherical Roller NTN open CN 1540 1720 34400
22328EAKD1 Spherical Roller NTN open CN 1540 1720 33700
22328EMD1 Spherical Roller NTN open CN 1540 1720 35400
22328EMKD1 Spherical Roller NTN open CN 1540 1720 34700
N2328 Cylindrical Roller NTN open CN 1020 1250 33100
NCF2328-ECJB Cylindrical Roller SKF open CN 1250 1530 35500
NJ2328 Cylindrical Roller NTN open CN 1020 1250 33100
NJ2328-ECML Cylindrical Roller SKF open CN 1200 1430 36500
NJ2328E Cylindrical Roller NTN open CN 1130 1380 —
NJG2328-VH Cylindrical Roller SKF open CN 1230 1660 35500
NU2328 Cylindrical Roller NTN open CN 1020 1250 33100
NU2328-ECML Cylindrical Roller SKF open CN 1200 1430 36000
NU2328E Cylindrical Roller NTN open CN 1130 1380 —
NUH2328-ECMH Cylindrical Roller SKF open CN 1250 1530 35000
NUP2328 Cylindrical Roller NTN open CN 1020 1250 33100
NUP2328-ECML Cylindrical Roller SKF open CN 1200 1430 37000
NUP2328E Cylindrical Roller NTN open CN 1130 1380 —
SL192328-TB-XL-BR Cylindrical Roller FAG open CN 1410 1570 34900

Note: catalogue dynamic load ratings for this envelope span 1020.0– 1540.0 kN — a 51% spread between designs in the very same 140×300×102 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 140 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 22328, 22328-CCK-W33, 22328EAD1, 22328EAKD1, 22328EMD1, 22328EMKD1, N2328, NCF2328-ECJB, NJ2328, NJ2328-ECML, NJ2328E, NJG2328-VH, NU2328, NU2328-ECML, NU2328E, NUH2328-ECMH, NUP2328, NUP2328-ECML, NUP2328E, SL192328-TB-XL-BR.

Frequently asked questions

Are all 140×300×102 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 140 mm bore, 300 mm OD, 102 mm width (5.512×11.811×4.016 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 20 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 140×300×102?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 140×300×102 mm in inches?

140×300×102 mm converts to 5.512×11.811×4.016 in, with a 80 mm (3.150 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 22328, 22328-CCK-W33, 22328EAD1 mount in the same space despite different internal designs.