NUP2328-ECML bearing: complete specifications & equivalents
The NUP2328-ECML is a ISO 15 radial bearing sized 140 x 300 x 102 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 140 mm |
| Outer diameter D | 300 mm |
| Width B | 102 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass |
| Basic dynamic load rating C | 1200 kN |
| Basic static load rating C0 | 1430 kN |
| Fatigue load limit Pu | 150 kN |
| Reference speed (thermal) | 2400 rpm |
| Limiting speed (mechanical) | 4300 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 37000 g |
| Manufacturer designation | SKF NUP 2328 ECML |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NUP2300-series range
| Bore d | 5.512 in |
|---|---|
| Outer diameter D | 11.811 in |
| Width B | 4.016 in |
| ISO bore code | 28 |
| Radial section height (D−d)/2 | 80 mm |
| Smallest bore in NUP2300-series | 20 mm |
| Largest outer diameter in NUP2300-series | 300 mm |
| Width range across NUP2300-series | 21–102 mm |
| Bore position in NUP2300-series (smallest first) | 21 of 21 |
| Bore above smallest NUP2300-series size | 120 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NJ2328-ECML | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 140×300×102 mm and equivalent catalogue ratings; the NJ execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
| NU2328-ECML | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 140×300×102 mm and equivalent catalogue ratings; the NU execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NUP2328-ECML model number is decoded
In SKF catalogue PUB BU/P1 17000, SKF NUP 2328 ECML denotes a single-row caged cylindrical roller bearing on the ISO 15 140×300×102 mm envelope, dimension series 23 (medium-section, wide), with catalogue mass 37000 g. Structurally, the NUP design has two integral flanges on the outer ring plus one integral flange and one loose flange ring on the inner ring. In arrangement terms it is a locating bearing that positions the shaft axially in both directions while keeping the cylindrical-roller radial capacity. Reading the order-string suffix ECML: the E-design ECML execution with a one-piece machined brass cage for higher-temperature, higher-speed continuous duty. Load-per-bore for the 140 mm seat is about 8.57 kN/mm, typical of dimension series 23 (medium-section, wide); use C0 1430 kN for static checks such as crane hook blocks standing under load. Fit practice for NUP2328-ECML: the loose inner-ring flange must be fitted on the correct side and retained by the shaft abutment; never omit it during reassembly or the bearing loses its two-direction locating function. Single-row cylindrical rollers tolerate only about 3–4 minutes of arc misalignment, so verify shaft and housing alignment.
Typical equipment & failure modes
Common applications
- offshore drawworks shafts
- large rolling-mill drive trains
- marine propulsion line shafts
- heavy turbogenerator rotor supports
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- cage pocket wear from roller skew at light load
- cage pocket wear from roller skidding at insufficient radial load or during start-up before oil film build-up
- surface distress (micro-pitting) when the EHL film falls below the composite roughness at high specific load
- edge-loading fatigue after shaft deflection beyond the 3–4 minute alignment limit
- brinelling from static overload or impact during handling and mounting
Selection pitfalls — read before you substitute
- Do not use a NUP bearing where a floating non-locating bearing is required — the loose inner flange makes it a locating bearing
- The dimension series 23 (medium-section, wide) envelope is shared with the N/NU/NJ/NUP executions of 2328, but flange configuration and axial-locating behaviour differ — quote the full SKF NUP 2328 ECML and do not substitute rib styles without checking the shaft locating scheme.
- Catalogue reference and limiting speeds are different criteria: observe the mechanical ceiling even when thermal calculations allow more.
- Press-fit force goes through ring faces only; driving a ring home through the rollers brinells the 300 mm raceway.
- The 1200/1430 kN ratings are SKF catalogue 17000 (2018) values for the ECML execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NUP2328-ECML?
SKF NUP 2328 ECML is a single-row caged cylindrical roller bearing with 140 mm bore, 300 mm OD and 102 mm width per ISO 15. SKF lists C 1200 kN, C0 1430 kN, Pu 150 kN, reference speed 2,400 r/min and limiting speed 4,300 r/min, mass about 37000 g.
What does the NUP designation and ECML suffix mean?
The ECML suffix denotes the E-design execution with a one-piece machined brass cage for higher-temperature and higher-speed continuous duty. Structurally this execution has two integral flanges on the outer ring plus one integral flange and one loose flange ring on the inner ring.
Can NUP2328-ECML take axial load and locate the shaft?
Yes, in both directions: the integral inner flange plus the loose flange ring close both axial paths. Do not pair it with another locating bearing without thermal clearance.
How does NUP2328-ECML compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.