319434-B-2LS bearing: complete specifications & equivalents
The 319434-B-2LS is a ISO 15 radial bearing sized 170 x 230 x 80 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 170 mm |
| Outer diameter D | 230 mm |
| Width B | 80 mm |
| Material | GCr15 |
| Seal / shield | 2RS |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 512 kN |
| Basic static load rating C0 | 1060 kN |
| Fatigue load limit Pu | 110 kN |
| Reference speed (thermal) | 530 rpm |
| Limiting speed (mechanical) | 530 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 9200 g |
| Manufacturer designation | SKF 319434 B-2LS |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.5 sealed double-row full complement cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.5 sealed double-row full complement cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.5 sealed double-row full complement cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NNF4900-series range
| Bore d | 6.693 in |
|---|---|
| Outer diameter D | 9.055 in |
| Width B | 3.15 in |
| ISO bore code | 34 |
| Radial section height (D−d)/2 | 30 mm |
| Smallest bore in NNF4900-series | 130 mm |
| Largest outer diameter in NNF4900-series | 340 mm |
| Width range across NNF4900-series | 80–95 mm |
| Bore position in NNF4900-series (smallest first) | 5 of 11 |
| Bore above smallest NNF4900-series size | 40 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the 319434-B-2LS model number is decoded
SKF 319434 B-2LS is a sealed double-row full-complement cylindrical roller bearing sized 170×230×80 mm — a dimension series 3194, listed in SKF catalogue PUB BU/P1 17000 ch. 6.5. Structurally, the NNF design has a double-row full complement bearing with contact seals on both sides, three integral inner-ring flanges, an annular lube groove in the outer ring and additional lubrication holes in the inner ring, delivered grease-packed. In arrangement terms it is a sealed locating unit for very heavy radial loads; the sealed-for-life execution is the classic crane-sheave bearing. The six-digit order number is SKF's earlier designation convention retained for this 49-series envelope; it is still the factory order number rather than an NNF-series code. Reading the order-string suffix B-2LS: nitrile-rubber contact seals on both sides of a grease-packed full-complement unit. The radial section height is 30.0 mm and the catalogue mass 9200 g; at 512 kN dynamic rating this is roughly 3.01 kN of C per millimetre of bore before application factors. Mounting: mount as a complete sealed unit — never wash out the factory grease; the seals set the speed ceiling, and relubrication, where specified, goes through the ring grooves. A 170 mm seat normally takes a m6 interference with an H6 housing bore when the inner ring rotates.
Typical equipment & failure modes
Common applications
- heavy dock and shipyard crane systems
- mining dragline and shovel rope sheaves
- large offshore hook blocks and jib sheaves
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- seal-lip wear and grease loss in dusty crane and construction service after the relubrication interval is exceeded
- cage pocket wear from roller skidding at insufficient radial load or during start-up before oil film build-up
- surface distress (micro-pitting) when the EHL film falls below the composite roughness at high specific load
- grease degradation inside the sealed unit after long high-temperature periods, invisible until noise rises
- rolling-contact fatigue spalling after the rated L10 life is exceeded
Selection pitfalls — read before you substitute
- The sealed NNF unit is packed for life with the correct grease — do not heat it above the seal limit or wash it before mounting; damaged lip seals invalidate the heavy-load duty.
- The B1 width (79 mm inner-assembly width) differs from the overall B 80 mm; check housing and spacer geometry against both values.
- Catalogue reference and limiting speeds are different criteria, though only the limiting speed is published for this sealed unit: observe the mechanical ceiling even when thermal calculations allow more.
- Catalogue reference and limiting speeds are different criteria, though only the limiting speed is published for this sealed unit: observe the mechanical ceiling even when thermal calculations allow more.
- The 512/1060 kN ratings are SKF catalogue 17000 (2018) values for the B-2LS execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of 319434-B-2LS?
SKF 319434 B-2LS is a sealed double-row full-complement cylindrical roller bearing with 170 mm bore, 230 mm OD and 80 mm width per ISO 15. SKF lists C 512 kN, C0 1060 kN, Pu 110 kN, limiting speed 530 r/min (sealed execution), mass about 9200 g. Inner-assembly width B1 is 79 mm.
What does the NNF designation and B-2LS suffix mean?
The B-2LS suffix denotes nitrile-rubber contact seals on both sides of a grease-packed full-complement unit. Structurally this execution has a double-row full complement bearing with contact seals on both sides, three integral inner-ring flanges, an annular lube groove in the outer ring and additional lubrication holes in the inner ring, delivered grease-packed.
Can 319434-B-2LS take axial load and locate the shaft?
The sealed NNF unit can guide light axial loads in both directions via the flanged inner ring, but its primary duty is very heavy radial load in sealed positions.
How does 319434-B-2LS compare with the other executions in the same envelope?
The sealed NNF execution shares its envelope with the open NNCF/NNCL/NNC full-complement bearings but is delivered grease-packed with contact seals and a much lower speed ceiling.
Does the sealed NNF bearing need relubrication?
NNF bearings are delivered grease-packed and sealed for long service; where the design provides relubrication grooves/holes, replenish through them at the prescribed interval. Never wash the bearing out or exceed the seal-limited speed.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.5 sealed double-row full complement cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.