NUP316-ECP bearing: complete specifications & equivalents
The NUP316-ECP is a ISO 15 radial bearing sized 80 x 170 x 39 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 80 mm |
| Outer diameter D | 170 mm |
| Width B | 39 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | polymer (PA66 glass-fibre reinforced) |
| Basic dynamic load rating C | 300 kN |
| Basic static load rating C0 | 290 kN |
| Fatigue load limit Pu | 36 kN |
| Reference speed (thermal) | 4300 rpm |
| Limiting speed (mechanical) | 5000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 4100 g |
| Manufacturer designation | SKF NUP 316 ECP |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NUP300-series range
| Bore d | 3.15 in |
|---|---|
| Outer diameter D | 6.693 in |
| Width B | 1.535 in |
| ISO bore code | 16 |
| Radial section height (D−d)/2 | 45 mm |
| Smallest bore in NUP300-series | 20 mm |
| Largest outer diameter in NUP300-series | 300 mm |
| Width range across NUP300-series | 15–62 mm |
| Bore position in NUP300-series (smallest first) | 13 of 21 |
| Bore above smallest NUP300-series size | 60 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| N316-ECP | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 80×170×39 mm and equivalent catalogue ratings; the N execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
| NJ316-ECP | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 80×170×39 mm and equivalent catalogue ratings; the NJ execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
| NU316 | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 80×170×39 mm and equivalent catalogue ratings; the NU execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
| NU316 | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 80×170×39 mm and equivalent catalogue ratings; the NU execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
| NU316 | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 80×170×39 mm and equivalent catalogue ratings; the NU execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NUP316-ECP model number is decoded
SKF NUP 316 ECP is a single-row caged cylindrical roller bearing sized 80×170×39 mm — a dimension series 3 (medium-section ISO 15 envelope), listed in SKF catalogue PUB BU/P1 17000 ch. 6.1. Reading the NUP prefix: two integral flanges on the outer ring plus one integral flange and one loose flange ring on the inner ring. This makes the execution a locating bearing that positions the shaft axially in both directions while keeping the cylindrical-roller radial capacity. The ECP suffix marks the E-design execution with a glass-fibre reinforced polyamide (PA66) cage, limited to 120 °C continuous. With C 300 kN and C0 290 kN, size the bearing on the 80×170 mm ISO 15 envelope and check the 36 kN Pu against the equivalent-load floor; the catalogue lists 4,300 r/min thermal reference speed and 5,000 r/min mechanical limiting speed. Mounting: the loose inner-ring flange must be fitted on the correct side and retained by the shaft abutment; never omit it during reassembly or the bearing loses its two-direction locating function. A 80 mm seat normally takes a k5 interference with an H6 housing bore when the inner ring rotates.
Typical equipment & failure modes
Common applications
- rolling-mill auxiliary drive shafts
- paper-machine press rolls
- cement-plant conveyor drives
- heavy gearbox and pinion shafts
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- polymer cage softening above 120 °C
- cage pocket wear from roller skidding at insufficient radial load or during start-up before oil film build-up
- roller-end scoring from inadequate oil flow in the roller-raceway contact
- edge-loading fatigue after shaft deflection beyond the 3–4 minute alignment limit
- hard-particle indentation of the raceway in unfiltered oil systems
Selection pitfalls — read before you substitute
- Do not use a NUP bearing where a floating non-locating bearing is required — the loose inner flange makes it a locating bearing
- The dimension series 3 (medium-section ISO 15 envelope) envelope is shared with the N/NU/NJ/NUP executions of 316, but flange configuration and axial-locating behaviour differ — quote the full SKF NUP 316 ECP and do not substitute rib styles without checking the shaft locating scheme.
- Shaft and housing fillets must clear the bearing chamfers; an oversized radius tilts the 39 mm-wide ring and concentrates load.
- Press-fit force goes through ring faces only; driving a ring home through the rollers brinells the 170 mm raceway.
- The 300/290 kN ratings are SKF catalogue 17000 (2018) values for the ECP execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NUP316-ECP?
SKF NUP 316 ECP is a single-row caged cylindrical roller bearing with 80 mm bore, 170 mm OD and 39 mm width per ISO 15. SKF lists C 300 kN, C0 290 kN, Pu 36 kN, reference speed 4,300 r/min and limiting speed 5,000 r/min, mass about 4100 g.
What does the NUP designation and ECP suffix mean?
The ECP suffix marks the E-design execution with a glass-fibre reinforced polyamide (PA66) cage, limited to 120 °C continuous. Structurally this execution has two integral flanges on the outer ring plus one integral flange and one loose flange ring on the inner ring.
Can NUP316-ECP take axial load and locate the shaft?
Yes, in both directions: the integral inner flange plus the loose flange ring close both axial paths. Do not pair it with another locating bearing without thermal clearance.
How does NUP316-ECP compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.