HK1010 bearing: complete specifications & equivalents
The HK1010 is a ISO 3245 radial bearing sized 10 x 14 x 10 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 10 mm |
| Outer diameter D | 14 mm |
| Width B | 10 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 4.29 kN |
| Basic static load rating C0 | 5.3 kN |
| Fatigue load limit Pu | 0.57 kN |
| Reference speed (thermal) | 18000 rpm |
| Limiting speed (mechanical) | 20000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 4.1 g |
| Manufacturer designation | HK 1010 |
| Standard | ISO 3245 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & HK-series range
| Bore d | 0.394 in |
|---|---|
| Outer diameter D | 0.551 in |
| Width B | 0.394 in |
| ISO bore code | 10 |
| Radial section height (D−d)/2 | 2 mm |
| Smallest bore in HK-series | 3 mm |
| Largest outer diameter in HK-series | 68 mm |
| Width range across HK-series | 6–38 mm |
| Bore position in HK-series (smallest first) | 8 of 26 |
| Bore above smallest HK-series size | 7 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| HK1010FM | NTN | full Dimensions and internal design equivalent — standard interchange. | NTN counterpart on the same 10×14×10 mm envelope with ratings within 10 % — interchange after checking the execution (cage/seal) details on both pages. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HK1010 model number is decoded
The drawn cup bearing HK 1010 gives the smallest radial section of any caged needle bearing with its own outer ring: 10 mm Fw, 14 mm OD and 10 mm width, the shell pressed directly into the housing bore. In HK 1010, Fw = 10 mm names the shaft that becomes the inner raceway and B = 10 mm the cup width; the shell outside diameter 14 mm is fixed by the boundary plan, so the housing bore needs only a press-fit tolerance. Open caged execution: the standard HK drawn cup with steel cage, relubricable through the shaft where the housing allows. Drawn cups exist open (basic HK), sealed (2RS, with contact seals and grease fill) and with polymer TN cage; each is a separate order number with its own ratings, not a field conversion. Catalogue mass 4.1 g at 10×14×10 mm makes this one of the highest capacity-per-gram choices in the drawn cup needle roller bearings, open end; the limit is usually the shaft's ability to serve as a raceway, not the rolling contact itself. The shell is intentionally thin: seat it square with a slow press stroke, support the housing wall behind the bore, and stop the moment the cup face meets the shoulder — hammer blows split drawn cups.
Typical equipment & failure modes
Common applications
- office equipment and power tool gear trains
- steering column and pedal-box pivots in passenger cars
- idler gears and pulleys in small appliance drives
- spindle clusters of drilling and tapping units
Known failure patterns
- raceway spalling once the catalogue L10 life is exceeded or after overload events
- fretting corrosion of the cup outside diameter in a soft or oversized housing bore
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- brinelling of raceways from impact or pressing force transmitted through the rolling elements
Selection pitfalls — read before you substitute
- On a 10 mm seat the housing bore quality dominates life: a bore 0.02 mm out of round pinches the 14 mm ring or cup into a lobed shape, and the rollers then trace the housing's geometry error, not the design load.
- Hardness is load capacity: in families without an inner ring the 10 mm journal must hold 58–64 HRC with a ground finish; a surface that looks fine but sits at 45 HRC will rib the raceway within weeks.
- The quoted 4.29/5.3 kN ratings are SKF catalogue values for this exact execution (HK 1010); ratings can be revised without the order number changing, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the drawing.
- The 4.29/5.3 kN ratings and 4.1 g mass are SKF catalogue values transcribed from ch. 7.2 of PUB BU/P1 17000 (PDF table page 620); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
Can the HK 1010 run on an unhardened shaft?
No. In this execution the 10 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
How should the HK 1010 be mounted?
Press the cup in with a shouldered mandrel bearing on the stamped face, into a housing bore sized for a firm press fit; never hammer it or press through the rollers. Then slide the hardened shaft in. For 2RS executions the seals and grease are already in place — no additional sealing is needed.
What limits the service life of a HK 1010?
Beyond the L10 rating, the practical limits are journal/raceway hardness for the 10 mm seat, lubricant condition at the roller ends, and contamination through open ends — the 2.0 mm radial section leaves no reserve once a raceway is dented or ribboned.
What are the dimensions and ratings of the HK 1010?
A HK 1010 measures 10 mm bore/Fw × 14 mm outside diameter × 10 mm width (0.394 × 0.551 × 0.394 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 4.29 kN, static C0 5.3 kN, fatigue limit Pu 0.57 kN, limiting speed 20,000 r/min, reference speed 18,000 r/min, mass about 4.1 g.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings on 2026-09-26. Read our editorial & correction policy.