HK1015 bearing: complete specifications & equivalents
The HK1015 is a ISO 3245 radial bearing sized 10 x 14 x 15 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 10 mm |
| Outer diameter D | 14 mm |
| Width B | 15 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 6.6 kN |
| Basic static load rating C0 | 9 kN |
| Fatigue load limit Pu | 1.02 kN |
| Reference speed (thermal) | 18000 rpm |
| Limiting speed (mechanical) | 20000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 6 g |
| Manufacturer designation | HK 1015 |
| Standard | ISO 3245 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & HK-series range
| Bore d | 0.394 in |
|---|---|
| Outer diameter D | 0.551 in |
| Width B | 0.591 in |
| ISO bore code | 15 |
| Radial section height (D−d)/2 | 2 mm |
| Smallest bore in HK-series | 3 mm |
| Largest outer diameter in HK-series | 68 mm |
| Width range across HK-series | 6–38 mm |
| Bore position in HK-series (smallest first) | 8 of 26 |
| Bore above smallest HK-series size | 7 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| HK1015 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HK1015 model number is decoded
For a 10 mm shaft in a thin housing wall, SKF catalogue execution HK 1015 offers a 15 mm wide, 14 mm diameter pressed shell with caged needle rollers — the classic minimal-section drawn cup solution. The designation HK 1015 encodes geometry only — there is no bore code to decode, since the 10 mm Fw is printed directly in the first digits and the cup width 15 mm in the last two. Open caged execution: the standard HK drawn cup with steel cage, relubricable through the shaft where the housing allows. Drawn cups exist open (basic HK), sealed (2RS, with contact seals and grease fill) and with polymer TN cage; each is a separate order number with its own ratings, not a field conversion. Catalogue mass 6 g at 10×14×15 mm makes this one of the highest capacity-per-gram choices in the drawn cup needle roller bearings, open end; the limit is usually the shaft's ability to serve as a raceway, not the rolling contact itself. The shell is intentionally thin: seat it square with a slow press stroke, support the housing wall behind the bore, and stop the moment the cup face meets the shoulder — hammer blows split drawn cups.
Typical equipment & failure modes
Common applications
- office equipment and power tool gear trains
- steering column and pedal-box pivots in passenger cars
- idler gears and pulleys in small appliance drives
- spindle clusters of drilling and tapping units
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- drawn-cup shell distortion or splitting from a careless press-in without a seating mandrel
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- false brinelling of standby equipment under external vibration
Selection pitfalls — read before you substitute
- On a 10 mm seat the housing bore quality dominates life: a bore 0.02 mm out of round pinches the 14 mm ring or cup into a lobed shape, and the rollers then trace the housing's geometry error, not the design load.
- The quoted 6.6/9 kN ratings are SKF catalogue values for this exact execution (HK 1015); ratings can be revised without the order number changing, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the drawing.
- Oscillating pivots fail differently: rocking through a small angle concentrates wear in the same roller positions — inspect those zones, and consider rotating the assembly's clock position at service intervals.
- The 6.6/9 kN ratings and 6 g mass are SKF catalogue values transcribed from ch. 7.2 of PUB BU/P1 17000 (PDF table page 620); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
Does the HK 1015 need a hardened and ground shaft?
No. In this execution the 10 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
What mounting mistakes ruin a HK 1015?
Press the cup in with a shouldered mandrel bearing on the stamped face, into a housing bore sized for a firm press fit; never hammer it or press through the rollers. Then slide the hardened shaft in. For 2RS executions the seals and grease are already in place — no additional sealing is needed.
Is the HK 1015 sealed?
No — the open-end HK cup has no seals: the housing must keep contamination out and grease in. The 2RS execution of the same code adds both-side contact seals with a grease fill.
Which dimensions does the HK 1015 have?
A HK 1015 measures 10 mm bore/Fw × 14 mm outside diameter × 15 mm width (0.394 × 0.551 × 0.591 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 6.6 kN, static C0 9 kN, fatigue limit Pu 1.02 kN, limiting speed 20,000 r/min, reference speed 18,000 r/min, mass about 6 g.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings on 2026-09-26. Read our editorial & correction policy.