HK2220-2RS bearing: complete specifications & equivalents
The HK2220-2RS is a ISO 3245 radial bearing sized 22 x 28 x 20 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 22 mm |
| Outer diameter D | 28 mm |
| Width B | 20 mm |
| Material | GCr15 |
| Seal / shield | 2RS |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 13 kN |
| Basic static load rating C0 | 22.4 kN |
| Fatigue load limit Pu | 2.6 kN |
| Limiting speed (mechanical) | 7500 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 23 g |
| Manufacturer designation | HK 2220.2RS |
| Standard | ISO 3245 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & HK-series range
| Bore d | 0.866 in |
|---|---|
| Outer diameter D | 1.102 in |
| Width B | 0.787 in |
| ISO bore code | 20 |
| Radial section height (D−d)/2 | 3 mm |
| Smallest bore in HK-series | 3 mm |
| Largest outer diameter in HK-series | 68 mm |
| Width range across HK-series | 6–38 mm |
| Bore position in HK-series (smallest first) | 17 of 26 |
| Bore above smallest HK-series size | 19 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| HK2220F | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | NTN bearing on the same 22×28×20 mm envelope, but catalogue C/C0 differ (13/22.4 vs 16.8/28.8 kN) — envelope interchange only after a load check. |
| HK2220 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 22×28×20 mm envelope, but catalogue C/C0 differ between the executions (13/22.4 vs 15.7/29 kN) — boundary dimensions match, not a load-rating equivalent. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HK2220-2RS model number is decoded
The drawn cup bearing HK 2220.2RS gives the smallest radial section of any caged needle bearing with its own outer ring: 22 mm Fw, 28 mm OD and 20 mm width, the shell pressed directly into the housing bore. SKF's HK numbering puts the shaft size first: 22 → Fw 22 mm (the ground, hardened journal), 20 → width 20 mm, with the 28 mm shell OD from the ISO 3245 dimension table. Sealed 2RS execution: rubber contact seals on both cup faces, factory grease fill, and the slightly lower ratings of a sealed drawn cup — 13 kN C against the open bearing of the same code. The suffix TN denotes the glass fibre reinforced PA66 cage; the 2RS execution adds rubber contact seals on both faces, retaining factory grease for life-lubricated pivots. Catalogue mass 23 g at 22×28×20 mm makes this one of the highest capacity-per-gram choices in the drawn cup needle roller bearings, open end; the limit is usually the shaft's ability to serve as a raceway, not the rolling contact itself. Open ends mean the housing must do the sealing; where that is impossible, the 2RS execution with its integrated seals and grease fill replaces sealing rings that would not fit the 20 mm section.
Typical equipment & failure modes
Common applications
- office equipment and power tool gear trains
- steering column and pedal-box pivots in passenger cars
- idler gears and pulleys in small appliance drives
- spindle clusters of drilling and tapping units
Known failure patterns
- raceway spalling once the catalogue L10 life is exceeded or after overload events
- fretting corrosion of the cup outside diameter in a soft or oversized housing bore
- grease starvation at the roller ends when relubrication intervals are stretched in dirty duty
- hard-particle indentation in unfiltered lubricant
Selection pitfalls — read before you substitute
- On a 22 mm seat the housing bore quality dominates life: a bore 0.02 mm out of round pinches the 28 mm ring or cup into a lobed shape, and the rollers then trace the housing's geometry error, not the design load.
- Hardness is load capacity: in families without an inner ring the 22 mm journal must hold 58–64 HRC with a ground finish; a surface that looks fine but sits at 45 HRC will rib the raceway within weeks.
- The quoted 13/22.4 kN ratings are SKF catalogue values for this exact execution (HK 2220.2RS); ratings can be revised without the order number changing, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the drawing.
- The 13/22.4 kN ratings and 23 g mass are SKF catalogue values transcribed from ch. 7.2 of PUB BU/P1 17000 (PDF table page 622); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
Can the HK 2220.2RS run on an unhardened shaft?
No. In this execution the 22 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
How should the HK 2220.2RS be mounted?
Press the cup in with a shouldered mandrel bearing on the stamped face, into a housing bore sized for a firm press fit; never hammer it or press through the rollers. Then slide the hardened shaft in. For 2RS executions the seals and grease are already in place — no additional sealing is needed.
What limits the service life of a HK 2220.2RS?
Beyond the L10 rating, the practical limits are journal/raceway hardness for the 22 mm seat, lubricant condition at the roller ends, and contamination through open ends — the 3.0 mm radial section leaves no reserve once a raceway is dented or ribboned.
What are the dimensions and ratings of the HK 2220.2RS?
A HK 2220.2RS measures 22 mm bore/Fw × 28 mm outside diameter × 20 mm width (0.866 × 1.102 × 0.787 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 13 kN, static C0 22.4 kN, fatigue limit Pu 2.6 kN, limiting speed 7,500 r/min, mass about 23 g.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings on 2026-09-26. Read our editorial & correction policy.