K15X21X15 bearing: complete specifications & equivalents
The K15X21X15 is a DIN 5402 radial bearing sized 15 x 21 x 15 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 15 mm |
| Outer diameter D | 21 mm |
| Width B | 15 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 13.8 kN |
| Basic static load rating C0 | 16.3 kN |
| Fatigue load limit Pu | 2 kN |
| Reference speed (thermal) | 24000 rpm |
| Limiting speed (mechanical) | 26000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 11 g |
| Manufacturer designation | K 15x21x15 |
| Standard | DIN 5402 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.1 needle roller and cage assemblies |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.1 needle roller and cage assemblies) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.1 needle roller and cage assemblies); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & K-series range
| Bore d | 0.591 in |
|---|---|
| Outer diameter D | 0.827 in |
| Width B | 0.591 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 3 mm |
| Smallest bore in K-series | 3 mm |
| Largest outer diameter in K-series | 63 mm |
| Width range across K-series | 7–32 mm |
| Bore position in K-series (smallest first) | 11 of 22 |
| Bore above smallest K-series size | 12 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the K15X21X15 model number is decoded
K 15x21x15 is a needle roller and cage assembly to DIN 5402: a complement of needle rollers held by a lightweight cage, with no inner or outer ring of its own — the 15 mm hardened shaft journal and the 21 mm housing bore serve as the raceways, as tabulated in SKF catalogue PUB BU/P1 17000. Reading the designation: K marks the needle roller and cage assembly, the three numbers give Fw 15 (shaft journal), E 21 (assembly outside diameter) and B 15 (width) in millimetres — the machine parts complete the bearing. SKF supplies these assemblies in single rows as tabulated; the cage quality determines the speed ceiling, and the catalogued 26,000 r/min limiting speed assumes a precision ground journal and bore. Speed planning separates the two ceilings: 24,000 r/min thermal reference and 26,000 r/min mechanical limiting — needle bearings tolerate high rpm only with adequate lubricant film at the 15 mm seat. The assembly is drawn on over a mounting sleeve that spreads the load around all rollers; never drive it home against the cage face, and retain it with a washer whose OD spans the cage, not the rollers.
Typical equipment & failure modes
Common applications
- rocker arm and rocker pin pivots on camshafts
- pump and gearbox idler gears running on hardened pins
- hinge and pivot joints in printing and textile machinery
- universal joint crosses on commercial vehicles
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- cage pocket wear and roller skew after sustained operation with too little radial preload
- grease starvation at the roller ends when relubrication intervals are stretched in dirty duty
- false brinelling of standby equipment under external vibration
- rapid raceway scoring when the shaft journal hardness drops below 58 HRC or the ground finish wears away
Selection pitfalls — read before you substitute
- On a 15 mm seat the housing bore quality dominates life: a bore 0.02 mm out of round pinches the 21 mm ring or cup into a lobed shape, and the rollers then trace the housing's geometry error, not the design load.
- Contamination, not fatigue, kills most small needle bearings: with raceways this narrow, one hard particle dents a full-width line — seal the housing even when the bearing execution itself is open.
- Do not interchange envelope-identical needle families blindly: K 15x21x15 shares its 15×21×15 mm outline with inner-ring and sealed siblings whose ratings differ — the family letters are part of the specification, not decoration.
- The 13.8/16.3 kN ratings and 11 g mass are SKF catalogue values transcribed from ch. 7.1 of PUB BU/P1 17000 (PDF table page 616); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
Is the K 15x21x15 sealed?
No — this execution is open and depends on the housing sealing arrangement; grease it at assembly and keep the relubrication interval short in dirty duty.
Which dimensions does the K 15x21x15 have?
A K 15x21x15 measures 15 mm bore/Fw × 21 mm outside diameter × 15 mm width (0.591 × 0.827 × 0.591 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 13.8 kN, static C0 16.3 kN, fatigue limit Pu 2 kN, limiting speed 26,000 r/min, reference speed 24,000 r/min, mass about 11 g.
What does K 15x21x15 mean in SKF part numbering?
K = needle roller and cage assembly (DIN 5402); the three figures give Fw 15 mm (shaft journal), E 21 mm (complement outside diameter, matched by the housing bore) and B 15 mm width. TN marks the glass fibre reinforced PA66 cage.
Does the K 15x21x15 need a hardened and ground shaft?
No. In this execution the 15 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.1 needle roller and cage assemblies on 2026-09-26. Read our editorial & correction policy.